Beretta MYNUTE X R, Инструкция по установке и эксплуатации

Страница: 22 / 132

22
MYNUTE X R
For fault E041
If the pressure drops below the safety threshold of 0.3 bar the boiler displays the fault code
<<E041 water transducer load the system>> for a transitional time of 30sec.
DAY
When the transitional time has finished, if the fault persists the fault code E040 is displayed .
When the boiler has fault E040 manual loading should be carried out using the filling tap ( external
to the boiler) until the pressure is between 1 and 1.5 bar. Then press RESET.
Close the filling tap (external to the boiler), making sure to hear the mechanical snap. At the end
of the procedure, proceed with the automatic vent cycle as described in the section "3.15 Filling
the heating system and eliminating air".
b
If the drop in pressure is very frequent, contact the Technical Assistance Centre.
For fault E060
The appearance of the E060 fault, on models with water tank with probe connected,
prevents sanitary operation.
For fault E091
The boiler has an auto-diagnostic system which, based on the total number of hours in
certain operating conditions, can signal the need to clean the primary exchanger (alarm
code E091). Once the cleaning operation (made with special kit supplied as an accessory)
it is necessary to reset to zero the total hour meter following procedure indicated below:
ƒ
access the technical parameters as explained in the section "3.19 Access to the
parameters"
ƒ
select the CONF menu and then EXHAUST PROBE RESET with the keys and
ƒ
set the parameter to 1 confirming the selection with
Enter
.
NOTE: The meter resetting procedure should be carried out after each in-depth cleaning
of the primary exchanger or if this latter is replaced.
The total hours can be verified in the following way:
ƒ
access the INFO menus as indicated in the paragraph "4.21 INFO menu" at EXHAUST
PROBE RESET to display the value of the flue gases probe meter.
Boiler faults list
ERROR
CODE
ERROR MESSAGE RED LED GREEN LED RED and GREEN
DESCRIPTION OF TYPE
OF ALARM
E010 flame lockout/ACF electronic fault ON definitive
E011 extraneous flame flashing 0.2 sec. on/0.2 off transitional
E020 limit thermostat flashing 0.5 sec. on/0.5 off definitive
E030 fan fault ON definitive
E040 water transducer – load the system ON definitive
E041 water transducer - load the system flashing 0.5 sec. on/0.5 off transitional
E042 water pressure transducer fault ON definitive
E060 storage tank probe fault flashing 0.5 sec. on/0.5 off transitional
E070
fault flow sensor/overtemperature flow sensor/
flow/return sensor differential alarm
ON
transitional/definitive/
definitive
E077 main zone water thermostat ON transitional
E080
fault return line probe/return line probe overtemperature/
outlet/return line probe differential alarm
ON
transitional/ definitive /
definitive
E090
fault flue gases probe/
flue gases overtemperature probe
flashing 0.5 sec. on/0.5 off
transitional
definitive
E091 clean primary heat exchanger flashing 0.5 sec. on/0.5 off transitional
E099 reset attempts exhausted, boiler blocked It is referred to the last fault occurred definitive, not resettable
-- water pressure low - check the system flashing 0.5 sec. on/0.5 off transitional
-- water pressure high - check the system flashing 0.5 sec. on/0.5 off transitional
-- boiler board communication lost ON transitional
-- BUS 485 communication lost ON transitional
List of combustion faults
ERROR CODE ERROR MESSAGE
LED
RED
LED
GREEN
DESCRIPTION OF TYPE OF ALARM
E021 iono alarm ON
These are temporary alarms that if they occur 6 times in an hour they become definitive;
the alarm E097 is displayed and is followed by post-purging for 45 seconds at the fan’s
maximum speed. It is not possible to release the alarm before the end of the post-purging
unless the boiler’s power supply is switched off.
E022 iono alarm ON
E023 iono alarm ON
E024 iono alarm ON
E067 iono alarm ON
E088 iono alarm ON
E097 iono alarm ON
E085 incomplete combustion ON
These are temporary alarms that if they occur several times in an hour they become de-
finitive; the last error to occur is displayed and is followed by a post-purging of 5 minutes
at the fan's maximum speed. It is not possible to release the alarm before the end of the
post-purging unless the boiler's power supply is switched off.
E094 incomplete combustion ON
E095 incomplete combustion ON