BenQ HT8050 Скачать руководство пользователя

Страница: 34 / 43

34 Maintenance

Replacing the lamp

1. Turn the power off and disconnect the projector from the power outlet. If the lamp is hot, avoid

burns by waiting for approximately 45 minutes until the lamp has cooled.

2. Locate the arrow mark on the lamp cover. Press where

the arrow mark is and push to slide the lamp cover in
the direction of the arrow.

3. Open the lamp cover.

The lamp MUST be replaced before the projector will operate
normally.
Press

to dismiss the message.

"XXXX" shown in the above messages are numbers that vary depending on different models.

• To reduce the risk of electrical shock, always turn the projector off and disconnect the power cord before

changing the lamp.

• To reduce the risk of severe burns, allow the projector to cool for at least 45 minutes before replacing the lamp.
• To reduce the risk of injuries to fingers and damage to internal components, use caution when removing lamp

glass that has shattered into sharp pieces.

• To reduce the risk of injuries to fingers and/or compromising image quality by touching the lens, do not touch the

empty lamp compartment when the lamp is removed.

• This lamp contains mercury. Consult your local hazardous waste regulations to dispose of this lamp in a proper

manner.

• To assure optimal performance from the projector, it is recommended that you purchase a qualified projector

lamp for lamp replacement.

• If lamp replacement is performed while the projector is suspended upside-down from the ceiling, make sure that

no one is underneath the lamp socket to avoid any possible injury or damage to the human eyes caused by
fractured lamp.

• Ensure good ventilation when handling broken lamps. We recommend that you use respirators, safety glasses,

goggles or face shield and wear protective clothing such as gloves.

Do not turn the power on with the lamp cover open.

Out of Lamp Usage Time

Replace lamp (refer to user manual)

then reset the lamp timer

Order a new lamp at www.BenQ.com

Notice

Replace Lamp Now

Lamp hour > XXXX Hours

Order a new lamp at www.BenQ.com

Notice

Содержание HT8050












































Результаты поиска

Содержание HT8050

Отзывы:

Похожие инструкции для HT8050

Бренды по названию

Популярные бренды

BenQ HT8050, Руководство пользователя

Результаты поиска

Содержание HT8050

Отзывы:

Похожие инструкции для HT8050

Бренды по названию

Популярные бренды