BenQ 2720S Скачать руководство пользователя

Страница: 41 / 67

Chapter 7 Maintenance

This chapter gives step by step instructions for maintaining the 2740S

film scanner.

7.1 Precaution

Make sure that you unplug the film scanner before disassembling.

Unless otherwise specified, reassemble the scanner by reversing the

disassembly procedure.

Do not disassemble the CCD board and lens.

If it is necessary to plug in the adapter cord and operate the scanner

after it is disassembled, pay special attention to the following:

Keep your hands and clothing well away from the operating or

moving parts such as scan module, gear train ...etc.

Never touches the terminals of the electrical and high-voltage

parts.

Unplug the connector by holding the connector housing. Pulling the

cable cord may cause poor connection. Turn the power off first when

unplug the connector on the scanner circuit board.

Never turn the power on if there is no shading on the lamp.

7.2 Housing Section

To removing housing

Remove the two screws in Figure 7-1.

Open the both side of the housing by the arrow direction, then pull out

the housing.

CAUTION:

Make sure there is not a strip holder or slide holder inserted

Maintenance API

Confidential

7-1

No Copy/Reproduction allowed

Содержание 2720S




































































Результаты поиска

Содержание 2720S

Отзывы:

Похожие инструкции для 2720S

Бренды по названию

Популярные бренды

BenQ 2720S, Руководство по обслуживанию

Результаты поиска

Содержание 2720S

Отзывы:

Похожие инструкции для 2720S

Бренды по названию

Популярные бренды