BendPak HD-7MZ Скачать руководство пользователя страница 7

Страница: 7 / 56

STEP 1

( Selecting Site )

Before installing your new lift, check the following:

1. LIFT LOCATION

: Always use architects plans when

available. Check layout dimension against floor plan

requirements making sure that adequate space if

available.

2. OVERHEAD OBSTRUCTIONS

: The area where

the lift will be located should be free of overhead

obstructions such as heaters, building supports, elec-

trical lines etc.

3. DEFECTIVE FLOOR

: Visually inspect the site where

the lift is to be installed and check for cracked or

defective concrete.

4. OPERATING TEMPERATURE:

Operate lift only

between temperatures of 41° -104° F.

5. Lift is designed for

INDOOR INSTALLATION ONLY.

Outdoor use is not permitted.

STEP 2

( Floor Requirements )

The lift must be installed on a solid, level, con-

crete floor with no more than 3-degrees of slope.

Failure to do so could cause personal injury or

death.

A level floor is suggested for proper use and

installation and level lifting. If a floor is of question-

able slope, consider a survey of the site and/or the pos-

sibility of pouring a new, level concrete slab.

DO NOT

install or use this lift on any asphalt surface

or any surface other than concrete.

DO NOT

install or use this lift on expansion seams

or on cracked or defective concrete.

DO NOT

install or use this lift on a second / elevated

floor without first consulting building architect.

CONCRETE SPECIFICATIONS

Lift Model

HD-7MZ

HD-7PXW

HD-7PXN

Concrete Requirements

4.25

” Min. Thickness / 3,000 PSI

4.25

” Min. Thickness / 3,000 PSI

4.25

” Min.

Thickness /

3,000 PSI

All models MUST be installed on 3

000 PSI or above con-

crete only, conforming to the requirements shown above.

New concrete must be adequately cured for a minimum of

28 days.

IMPORTANT NOTICE

These instructions must be followed to ensure proper installation and operation of your lift.

Failure to comply with these instructions can result in serious bodily harm and void product warranty.

Manufacturer will assume no liability for loss or damage of any kind, expressed or implied resulting

from improper installation or use of this product.

PLEASE READ ENTIRE MANUAL PRIOR TO INSTALLATION.

Rotary Hammer Drill or Similar

3/4” Masonry Bit

Hammer

4 Foot Level

Open-End Wrench Set: SAE/Metric

Socket And Ratchet Set: SAE/Metric

Hex-Key / Allen Wrench Set

Large A-Frame Ladder

Medium Crescent Wrench

Medium Pipe Wrench

Crow Bar

Chalk Line

Medium Flat Screwdriver

Tape Measure: 25 Foot Minimum

Needle Nose Pliers

TOOLS REQUIRED

NOTE:

An air supply (30 PSI Min / 3 CFM Min.) will be required for the safety-lock mechanisms. See Step 11.

Содержание HD-7MZ

























































Результаты поиска

Содержание HD-7MZ

Отзывы:

Похожие инструкции для HD-7MZ

Бренды по названию

Популярные бренды

BendPak HD-7MZ, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HD-7MZ

Отзывы:

Похожие инструкции для HD-7MZ

Бренды по названию

Популярные бренды