BendPak HD-7MZ Скачать руководство пользователя страница 42

Страница: 42 / 56

LIFT WILL NOT STAY UP

POSSIBLE CAUSE

1. Air in oil, (1,2,3)

5. Leaking fittings, (8)

2. Check valve leaks, (6)

4. Lowering valve leaks, (4,5,1,7,6)

3. Cylinders leak internally, (7)

REMEDY

INSTRUCTION

1. Check oil level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .The oil level should be up to the bleed screw in the

reservoir with the lift all the way down.

2. Oil seal damaged and cocked . . . . . . . . . . . . . . . . . . . . . . . . Replace oil seal around pump shaft.

3. Bleed cylinder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Refer to Installation Manual.

4. Flush release valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Hold release handle down and start unit allowing it to

run for 15 seconds.

5. Replace with new valve . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Replace with new valve.

6. Return unit for repair . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Return unit for repair.

7. See Installation Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Consult Lift Manufacturer.

8. Check complete hydraulic system for leaks. . . . . . . . . . . . . . .Tighten all hydraulics fittings and inspects all hoses.

Содержание HD-7MZ

























































Результаты поиска

Содержание HD-7MZ

Отзывы:

Похожие инструкции для HD-7MZ

Бренды по названию

Популярные бренды

BendPak HD-7MZ, Инструкция по установке и эксплуатации

Результаты поиска

Содержание HD-7MZ

Отзывы:

Похожие инструкции для HD-7MZ

Бренды по названию

Популярные бренды