BendPak 5175820, Руководство по обслуживанию

Страница: 23 / 33

14
12
13
11
16
15
7
6
1
5
21
3
10
4
9
2
8
19
22
20
18
17
ISOMETRIC VIEW
FOR REFERENCE ONLY
DO NOT SCALE
WHERE USED
HD-9AE
ITEM
NO.
PART
NUMBER
DESCRIPTION QTY REV
1 5701094 HD-7500BLX/9STX/9SWX/ 9XW/9AE EXTENDED RAMP 1 E
2 5746190 HD-7/7500/9 RAMP SHEAVE BUSHING 4 C
3 5755019 AIR LINE TROUGH Ø13.5 x Ø9.5 x 203 1 B
4 5735090 HD-7/7500/9 RAMP STRAP 1 C
5 5735091 HD-7500/9 SERIES CYLINDER CLEVIS 1 C
6 5700192 HD-7/7500/9 ROLLING BRIDGE BEAM, LONG 1 D
7 5735032 ROLLING JACK RAIL CLOSEOUT 2 C
8 5735028 PIN STOP 4 B
9 5755023 AIR LINE TROUGH Ø13.5 x Ø9.5 x 3454 1 B
10 5700300 HYDRAULIC HOSE HOLDER 2 A
11 5755090 HD-7/7500/9 DRIVE UP RAMP HINGE TUBE 4 C
12 5620474 HD-9AE LONG RISER WELDMENT 1 A
13 5700285 HD-9AE SMALL RISER PLATE 1 A
14 5620475 HD-9AE MEDIUM RISER WELDMENT 1 A
15 5755008 ALIGMENT CASTER SPACER 27 B
16 5755009 CASTER RETAINER 27 B
17 5746018 LOCATOR TUBE 4 B
18 5736203 HD-7500/9/973 RIGHT RAMP BOLT PLATE, 4-SHEAVE 1 D
19 5736204 HD-7500/9/973 LEFT RAMP BOLT PLATE, 4-SHEAVE 1 D
20 5736200 HD-7500/9 RAMP END PLATE, 4-SHEAVE 1 B
21 5736202 HD-7/7500/9 RAMP BOLT PLATE, 2-SHEAVE 1 D
22 5736201 HD-7/7500/9 RAMP END PLATE, 2-SHEAVE 1 B
REVISION
REV DESCRIPTION DATE EDITED BY ECO#
C UPDATED BOM REVISION 09/02/2014 TM 00664
D
D-001
D-002
REMOVED 5760090
ADDED RAL NUMBER TO NOTES
ADDED GLOSS NOTE TO PAINT, REMOVED GRIT
NOTE
04/22/2016
01/06/2017
02/03/2020
TM
TS
CA
00741
00798
01120
E
PLACEMENT OF 5755090: REMOVED WELD
FROM BOTTOM, SPECIFIED FULL WELD ON TOP,
UPDATED BOM REVISIONS
12/09/2021 TM 01367
NEXT ASSEMBLY
5215512 SHEET 1 OF 4
REV DWG. NO.
A
SIZE
TITLE:
NAME DATE
CHECKED
DRAWN
E
1645 LEMONWOOD DR.
SANTA PAULA, CA 93060
PROPRIETARY AND CONFIDENTIAL
THE INFORMATION CONTAINED IN THIS DRAWING IS
THE SOLE PROPERTY OF BENDPAK INC. ANY
REPRODUCTION IN PART OR AS A WHOLE WITHOUT
THE WRITTEN PERMISSION OF BENDPAK INC. IS
PROHIBITED.
TM
5600594
HD-9AE POWER SIDE
RAMP WELDMENT
01/17/2011
DO NOT SCALE DRAWING
1:35 SCALE:
THIRD ANGLE PROJECTION
DIMENSIONS ARE IN MM
TOLERANCES:
0. = ±1.5
0.0 = ±0.5
SURFACE FINISH 1.6 ISO Ra µm
FOR MACHINED SURFACES
UNLESS OTHERWISE SPECIFIED
REFER TO MODEL FOR ADDITIONAL INFORMATION 1.
BREAK AND DEBURR ALL SHARP EDGES 0.3mm 2.
REMOVE ALL WELD SPLATTER 3.
DIMENSIONS SHOWN ARE AFTER PAINTING 4.
PAINT GRAY (RAL-7024) 20% GLOSS 5.
NOTE: UNLESS OTHERWISE SPECIFIED.