BendPak 1302BA-302 Скачать руководство пользователя страница 31

Страница: 31 / 68

Bender Operation Manual 31

8. Retract the die by lifting up on the control handle.

(See figure 2-C)

9. Separate the collar from the tubing. Remove tooling

and return to the storage area.

USING THE DOMING DIE TO FINISH TAIL PIPE ENDS

For a more finished look on tailpipe ends, you may use

the DOMING DIE to slightly dome the ends. To properly

do this, follow these simple steps. (See chart on page 12

for typical end finishing illustrations.)

1. Retract the swager cylinder completely by lifting the

valve handle up.

2. Install the DD-134/212 tool on the ST-1 adapter

attached to the end of the cylinder shaft.

3. Install the required HAC adapter collar around the

tubing and position within the swager clamp blocks.

4. Leave the maximum amount of tubing extended

beyond the inside edge of the adapter collar as

possible. This will keep any slight clamp marks that

may occur away from the end of the taiIpipe which

is usually exposed as it is installed on the vehicle.

(See figure 3-C)

5. Snug the collar back into the clamp blocks by gently

pushing back on the collar assembly.

6. Slowly, while depressing the valve handle down,

move the shaft forward until the tool contacts the

tubing. Be sure that the tool is centered with the

tubing.

7. Slowly, move the tool forward until the desired finish

is achieved. (See figure 1-A)

8. Retract the die by lifting up on the control handle.

Separate the collar from the tubing. Remove tooling

and return to the storage area.

USING THE HCT-214/212

This tool is for making header flanges or “collectors” on

2-1/4” and 2-1/2” pipe ends. This eliminates the need to

purchase a collector when installing header type

manifoIds.

Not included in standard tooling packages.

IMPORTANT NOTE:

When making a manifold flange, it is necessary to first

install the pipe flange or clamp around the tube prior to

finishing the ends.

To properly produce a header collector using the optional

HCT-214/212 tool follow these simple steps. (See chart

on page 12 for typical end finishing illustrations.)

1. Retract the swager cylinder completely by lifting the

valve handle up.

2. Install the HCT-214/212 on the ST-1 adapter attached

to the end of the cylinder shaft.

3. Install the required HAC adapter collar around the

tubing and position within the swager clamp blocks.

4. Leave at least 4” of tubing extended beyond the

inside edge of the adapter collar. (See figure 2-A)

Figure 2-C

Figure 2-A

Figure 3-C

Figure 1-A

Содержание 1302BA-302





































































Результаты поиска

Содержание 1302BA-302

Отзывы:

Похожие инструкции для 1302BA-302

Бренды по названию

Популярные бренды

BendPak 1302BA-302, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 1302BA-302

Отзывы:

Похожие инструкции для 1302BA-302

Бренды по названию

Популярные бренды