Bench Dog Tools 23238 Скачать руководство пользователя страница 11

Страница: 11 / 12

2. Make sure the Crown-Cut is tight

against the miter saw fence and at

least 1/2" clear of the blade’s path.

Also double-check that the molding

is upside down in the Crown-Cut.

3. Line up your mark and carefully make

the cut.

4. To cut the right-side molding, keep the

head of your miter saw at 45° to the left

and position the Crown-Cut and molding

to the left of the blade. Fig. 8.

5. Make sure the Crown-Cut is tight

against the miter saw fence and at

least 1/2" clear of the blade’s path.

Also double-check that the molding

is upside down in the Crown-Cut.

6. Line up your mark and carefully make

the cut.

Cutting a Right-Over-Left Splice Joint

1. To cut the left-side molding, swing the

head of your miter saw 45° to the right

and position the Crown-Cut and molding

to the right of the blade. Fig. 9.

2. Make sure the Crown-Cut is tight

against the miter saw fence and at

least 1/2" clear of the blade’s path.

Also double-check that the molding

is upside down in the Crown-Cut.

3. Line up your mark and carefully make

the cut.

4. To cut the right-side molding, keep the

head of your miter saw at 45° to the right

and position the Crown-Cut and molding

to the left of the blade. Fig. 10.

5. Make sure the Crown-Cut is tight

against the miter saw fence and at

least 1/2" clear of the blade’s path.

Also double-check that the molding

is upside down in the Crown-Cut.

6. Line up your mark and carefully make

the cut.

Check Rockler.com for updates. If you have further

questions, please contact our Technical Support

Department at 1-800-260-9663 or

[email protected]

Fig. 7 - Left-Over-Right Position A

Fig. 8 - Left-Over-Right Position B

Fig. 9 - Right-Over-Left Position A

Fig. 10 - Right-Over-Left Position B

Содержание 23238













Результаты поиска

Содержание 23238

Отзывы:

Похожие инструкции для 23238

Бренды по названию

Популярные бренды

Bench Dog Tools 23238, Инструкция по эксплуатации

Результаты поиска

Содержание 23238

Отзывы:

Похожие инструкции для 23238

Бренды по названию

Популярные бренды