7
Brewing Instructions
SETTING UP THE MACHINE FOR BREWING A 12-CUP CARAFE
IMPORTANT:
Before brewing, always check to make sure water level inside the water tank is past the 2 cup line
and add water if needed. Never exceed the 12 cup fill line.
NOTE:
The amount of brewed coffee will always be less than the amount of water placed into the water reservoir-
as much as 10% is absorbed by coffee grounds and filter.
NOTE:
At any time press the ON/OFF button to begin brew cycle.
1. Lift to open the Coffee maker lid. Fill carafe with cold tap water to the desired line and pour into water reservoir
at the back of the coffee maker. The stepped water level indicator can be easily viewed inside coffee maker.
2. Place empty carafe on the keep warm plate.
3. For added convenience, remove the permanent filter. Measure 1 level tablespoon or 1 scoop with the
provided scoop of drip or regular ground coffee for each cup of coffee desired. For stronger or milder
coffee, adjust amount of ground coffee to suit your taste.
4. Replace the permanent filter back into the filter holder and place back into the coffee maker. Close the lid.
5. Plug the power cord into 120V/60HZ power supply socket, the LCD background indicator will illuminate in
blue and “AM 12:00” will be displayed on the LCD. At that time, “12” will flash while “: 00” will steadily
light. To set the hour select between and
. Once the desired hour is reached push the PROG / CLOCK
button. The minute “00” will now flash. Again, toggle between the and
buttons to reach the desired
minute. To confirm push the PROG / CLOCK button. The coffee maker will beep.
NOTE:
The backlight indicator will go into sleep mode within 5 seconds if no further buttons are selected.
Brewing Coffee
1. Press the ON/OFF button to start the brew cycle. One beep will sound and the ON/OFF button will
illuminate. The Coffee maker will begin the brew cycle.
NOTE:
To interrupt the brew process at any time, press the ON/OFF button once. The coffee maker will beep
and the ON/OFF light in the button will go out. The screen will display the clock.
2. Upon completion of the brew cycle, wait at least 1 minute until the dripping coffee from the flow valve
into the carafe has stopped. The carafe lid should be kept in place to facilitate safe serving and help keep
coffee at a proper serving temperature. Tilt the carafe slightly and pour the hot coffee very slowly, so that
the flow of the brewed coffee does not exceed the width of the spout.
3. Once the brew cycle is complete, the coffee maker will beep and will go into the keep-warm mode.
At that time the LCD will show
. The keep warm time will count up from 0:00. When the coffee
maker reaches the preset keep warm time, three beeps can be heard and
will disappear.
4. During the KEEP WARM mode press the ON/OFF button once to turn the Coffee maker off when the carafe
is empty or when the coffee maker is not in use.
Setting The Clock
1. Press and hold the PROG / CLOCK button for 3 seconds to enter into the clock-setting mode. The LCD will
illuminate and the current hour will flash.
2. Press button once to increase the hour by one increment each time, or hold the button to increase
quickly. Press
once to decrease the hour by one increment each time, or hold the button to decrease
quickly. Once your desired hour time is achieved, press the PROG / CLOCK button to confirm.
3. At that time, the current minute digits will illuminate and flash.
4. Again, press the button once to increase one minute each time and press
once to decrease one
minute each time. Both buttons can be held to increase the minutes quickly. Once the desired minute has
been reached, press the PROG / CLOCK button to confirm. One beep can be heard and the set time
will appear.
5. The coffee maker will automatically switch from AM to PM once the hour passes 12.
6. If a mistake was made or to exit the clock setting mode, wait 5 seconds and the LCD will show the last
clock setting.
Содержание 14405
Страница 2: ......