Belden Grass Valley HCO-3901 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 45

background image

GUIDE TO INSTALLATION AND OPERATION

4

| HCO-3901

2 Installation

2.1 Installation in the Densité frame

The HCO-3901 and its associated rear connector rear panel must be mounted in a Densité-3 or Densité-3+ series
frame, or in a GV Node.

•

It is not necessary to switch off the frame’s power when installing or removing the card.

•

With a double-width rear panel installed, the HCO-3901 must be installed in the right-most of the two slots
covered by the panel in order to mate with the panel’s connectors.

•

If it is placed in the wrong slot, the front panel LED will flash red. Move the card to other slot for correct
operation. No damage will result to the card should this occur.

See the manual for your Densité frame for detailed instructions on installing cards and their associated rear panels.

2.2 Rear Connector Panels

There are three rear panels available for the HCO-3901. The table summarizes their features, and their layouts are
shown in the figure below.

HCO-3901-3DRP-R-EX

HCO-3901-3DRP-R

HCO-3901-3SRP-R

Single-slot-width panel

♦

Double-slot-width panel

♦

♦

Bypass Relay

♦

♦

♦

CONNECTORS

BNC BNC

DIN

Ref IN

♦

♦

♦

Ref IN loop out

♦

♦

GPI I/O

♦

♦

3G/HD/SD IN

1 and 2

♦

♦

♦

3

♦

♦

3G/HD/SD OUT

PGM 1

♦

♦

♦

PGM 2

(phase inverted)

♦

PVW 1A

(phase inverted)

♦

PVW 1

(1B on –EX rear)

♦

♦

♦

PVW 2A

(phase inverted)

♦

PVW 2

(2B on –EX rear)

♦

♦

PVW 3A

(phase inverted)

♦

PVW 3

(3B on –EX rear)

♦

♦

«
...
6
7
8
9
10
...
»

Содержание Grass Valley HCO-3901














































Отзывы:

Нет отзывов

Похожие инструкции для Grass Valley HCO-3901

Бренд: Raymarine Страницы: 12

Бренд: Jafar Страницы: 13

Бренд: ZETRON Страницы: 3

Бренд: Saab Страницы: 4

FOUNDATION 3730-5

Бренд: Samson Страницы: 132

Бренд: Samson Страницы: 68

Бренд: Samson Страницы: 128

Бренд: Samson Страницы: 68

Бренд: X-POWER Страницы: 24

Бренд: Samson Страницы: 80

Бренд: Haehne Страницы: 44

Бренд: Zennio Страницы: 30

Бренд: Zeta Страницы: 13

Бренд: K&G GROEP Страницы: 27

Бренд: CAME Страницы: 2

Бренд: CalAmp Страницы: 13

Бренд: Absima Страницы: 5

Бренд: Kampmann Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды