Belanger SUDZAMELEON ARCH Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 88

background image

SUDZAMELEON

®

ARCH

50

Belanger, Inc.® *PO BOX 5470 *Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

1MANUL956

Utilities

Initial Startup Procedures

Bayonet Nozzles

1) Working with a local chemical supplier set the chemical to water ratio in the delivery system

to the desired setting.

2) Close the Sudzameleon® air plenum vent which is located on the end of the driver side

plenum assembly.

3) Using the controller force on the function(s) for the fan, lights and chemical delivery.

4) Turn the air regulator up that feeds the MixStir® pump to 80psi and inspect the entire

machine for bubbles. The bubbles should be coming out of all the nozzle tips at about the
same consistency. If one or more of the tips are not passing fluid, turn off the functions to
inspect and clean the spray nozzles. Make sure that there are no water leaks at any of the
hose connections or nozzles.

5) After inspecting the Sudzameleon® and confirming there are no leaks and that bubbles are

coming out of all of the nozzle tips you can adjust, in any order, the following:



The ratio of the chemical/water mixture. Try to find the best combination of settings that

will produce the desired bubble but uses the least amount of chemical. This can be
done by changing out the tips that are supplied with the HydroMinder on the MixStir®.



During the installation of the Sudzameleon® nozzles the 3D mesh media bubble disks

were installed. The media disks can be switched to the coarse media bubble disks if a
different style bubble is desired.



This Startup Procedure began with the Air Plenum Vent closed this will allow all of the

air from the fan to pass thru the nozzle outlets. The vent can be opened at this time to
achieve the desired amount and consistency of bubbles.



The speed of the fan was wired to high capacity. If you need to change the speed to

low capacity you must re-wire the fan, be sure to turn off all power to the bay before
rewiring.

6) After all of the settings have been adjusted run a few test washes on various vehicles to

confirm that the desired bubble consistency and volume has been obtained.

«
...
52
53
54
55
56
...
»

Содержание SUDZAMELEON ARCH

























































































Отзывы:

Нет отзывов

Похожие инструкции для SUDZAMELEON ARCH

Бренд: BACtrack Страницы: 13

Бренд: TA Instruments Страницы: 35

Бренд: Danelec Страницы: 67

SC 2 Deluxe EasyFix

Бренд: Kärcher Страницы: 12

Бренд: Kärcher Страницы: 16

QNET Physics and Dynamics

Бренд: Quanser Страницы: 4

Бренд: XanLite Страницы: 4

Бренд: XFit Страницы: 16

BlackBox Series

Бренд: Nakamichi Страницы: 23

Бренд: Harken Страницы: 4

Бренд: A&D Страницы: 33

Бренд: +GF+ Страницы: 2

Unity for Pro-Flex Pivot

Бренд: Össur Страницы: 40

ICELOCK 234 LANYARD

Бренд: Össur Страницы: 94

Бренд: Össur Страницы: 115

Бренд: Össur Страницы: 253

Бренд: M-system Страницы: 4

Бренд: Lencarta Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды