Belanger SUDZAMELEON ARCH Скачать руководство пользователя страница 33

Страница: 33 / 88

SUDZAMELEON

ARCH

1MANUL956

Belanger®, Inc. *PO BOX 5470 *Northville, MI 48167-5470 * Ph (248) 349-7010 * Fax (248) 380-9681

Installation

Tunnel Placement

13) Verify the passenger leg is square and plumb in all directions using a level; shims may be used

under the foot plate if necessary.

14) Drill the lag holes in the concrete and use the supplie

d ½” lag bolts to secure the passenger

foot plate to the floor.

Note:

Remember to verify where any underground heat or utilities run so you can be sure to not

drill into them with the hammer drill when making the lag holes.

Note:

Do not hammer the lag bolts all the way down at this time, leave room to raise the foot plate

later if necessary.

Driver Side

Passenger Side

½” Lag Bolts

Содержание SUDZAMELEON ARCH

























































































Результаты поиска

Содержание SUDZAMELEON ARCH

Отзывы:

Похожие инструкции для SUDZAMELEON ARCH

Бренды по названию

Популярные бренды

Belanger SUDZAMELEON ARCH, Руководство пользователя

Результаты поиска

Содержание SUDZAMELEON ARCH

Отзывы:

Похожие инструкции для SUDZAMELEON ARCH

Бренды по названию

Популярные бренды