Beko WMB 50811 PL NY, Руководство пользователя

Страница: 5 / 36

5 / EN
Washing Machine / User’s Manual
2 Installation
Refer to the nearest Authorised Service Agent for installation
of the product. To make the product ready for use, review
the information in the user manual and make sure that the
electricity, tap water supply and water drainage systems are
appropriate before calling the Authorized Service Agent. If they
are not, call a qualified technician and plumber to have any
necessary arrangements carried out.
C
InformatIons
Preparation of the location and electrical, tap water and waste
water installations at the place of installation is under customer’s
responsibility.
Make sure that the water inlet and discharge hoses as well as the
power cable are not folded, pinched or crushed while pushing the
product into its place after installation or cleaning procedures.
B
WarnInG
Installation and electrical connections of the product must be
carried out by the Authorized Service Agent. Manufacturer shall not
be held liable for damages that may arise from procedures carried
out by unauthorized persons.
A
WarnInG
Prior to installation, visually check if the product has any defects on
it. If so, do not have it installed. Damaged products cause risks for
your safety.
2.1 appropriate installation location
• Place the machine on a rigid floor. Do not place it on a long
pile rug or similar surfaces.
• Total weight of the washing machine and the dryer -with
full load- when they are placed on top of each other
reaches to approx. 180 kilograms. Place the product on a
solid and flat floor that has sufficient load carrying capacity!
• Do not place the product on the power cable.
• Do not install the product at places where temperature may
fall below 0ºC.
• Place the product at least 1 cm away from the edges of
other furniture.
2.2 removing packaging reinforcement
Tilt the machine backwards to remove the packaging
reinforcement. Remove the packaging reinforcement by
pulling the ribbon.
2.3 removing the transportation locks
A
WarnInG
Do not remove the transportation locks before taking out the
packaging reinforcement.
Remove the transportation safety bolts before operating the
washing machine! Otherwise, the product will be damaged.
Loosen all the bolts with a suitable spanner until they rotate
freely (C). Remove transportation safety bolts by turning them
gently. Attach the plastic covers supplied in the User Manual
bag into the holes on the rear panel. (P)
C
InformatIons
Keep the transportation safety bolts in a safe place to reuse when
the washing machine needs to be moved again in the future.
Never move the product without the transportation safety bolts
properly fixed in place!
2.4 Connecting water supply
C
InformatIons
The water supply pressure required to run the product is between
1 to 10 bars (0.1 – 1 MPa). It is necessary to have 10 – 80 liters
of water flowing from the fully open tap in one minute to have your
machine run smoothly. Attach a pressure reducing valve if water
pressure is higher.
If you are going to use the double water-inlet product as a single
(cold) water-inlet unit, you must install the supplied stopper to
the hot water valve before operating the product. (Applies for the
products supplied with a blind stopper group.)
If you want to use both water inlets of the product, connect the
hot water hose after removing the stopper and gasket group from
the hot water valve. (Applies for the products supplied with a blind
stopper group.)
A
WarnInG
Models with a single water inlet should not be connected to the
hot water tap. In such a case the laundry will get damaged or the
product will switch to protection mode and will not operate.
Do not use old or used water inlet hoses on the new product. It may
cause stains on your laundry.
Connect the special hoses supplied with the product to the
water inlets on the product. Red hose (left) (max. 90 ºC) is for
hot water inlet, blue hose (right) (max. 25 ºC) is for cold water
inlet.
A
WarnInG
Ensure that the cold and hot water connections are made correctly
when installing the product. Otherwise, your laundry will come out
hot at the end of the washing process and wear out.
Tighten all hose nuts by hand. Never use a wrench when
tightening the nuts. Open the taps completely after making the
hose connection to check for water leaks at the connection
points. If any leaks occur, turn off the tap and remove the nut.
Retighten the nut carefully after checking the seal. To prevent
water leakages and damages caused by them, keep the taps
closed when the machine is not in use.