3
INSTALLATION INSTRUCTIONS EUROLIGHT LD6230
The BEHRINGER EUROLIGHT LD6230 Dimmer Pack was
developed to meet the highest demands of light engineering. Its
wide-ranging functions make it an all-purpose workhorse for
various commercial applications (TV studios, theatre or live
events).
The EUROLIGHT LD6230 has all the important features needed
to control your lighting equipment, yet its controls are clearly
arranged and simple to use. You can select between digital DMX
or analog control. You get trouble-free operation with the
extensive LEDs used for signal error detection.
IMPORTANT INFORMATION
+
Installation as well as initial operation must be
performed by qualified personnel.
Always assure
that your LD6230 is completely disconnected from
the mains before removing the casing cover.
+
The LD6230 was designed for indoor use only.
+
Please keep in mind that sudden temperature
changes (e.g. bringing your equipment from colder
environments into warmer environments) may
cause condensation on electronic components,
leading to possible equipment damage and physical
harm to the operator.
+
Please adhere to all applicable national safety
standards during installation.
+
Please read the installation instructions and the
enclosed users manual in their entirety to
familiarize yourself with the LD6230 and all of its
functions. Please follow all instructions and store
both the installation instructions and the manual in
a safe place for future reference.
+
Please assure that your EUROLIGHT is sufficiently
cooled and that it is not placed near heat sources
that could cause overheating.
+
If you want to run your EUROLIGHT on mains voltage
other than factory-specified voltage, contact the
nearest BEHRINGER service center.
+
To effectively limit harmonic currents and avoid
voltage fluctuations that could affect other electrical
appliances, connect this equipment to an AC outlet
that complies with all applicable technical standards.
In all other cases, contact your local power supply
provider for advice prior to usage.
MAINS/ILLUMINANT
CONNECTORS
To facilitate additional flexibility, your dimmer pack has a
connector terminal strip. Cable bushings for connecting to the
mains and your illuminants are located in the back. Flexibility is
further enhanced with the option to retrofit a CEE connector and
a 16-pin HARTING
®
connector.
Both fixed and mobile installations require compliance with IEC
61010-1:2001 (EN 6110-1:2001). In particular, a 3-phase
separator (pursuant IEC60947-1 and IEC60947-3) needs to be
included in the installation. This separator needs to be labeled
according to IEC 60417-50008 and IEC 0417-5007.
To assure compliance with
Directive 89/336/EEC
,
only use
specified upstream line filters with your EUROLIGHT. Using it
without line filters specified by BEHRINGER may lead to
electromagnetic interference. More detailed information on this
subject can be found at www.behringer.com.
SAFETY AND INITIAL OPERATION
As soon as you connect your LD6230 to the mains, internal
controls are activated. The six
automated fuses (circuit breakers)
can all handle 10 A and serve as overload protection for the
connected equipment.
+
Please keep in mind that activating circuit breakers
1, 2, 3, 4, 5 or 6 also means that the respective
channels can conduct voltage.
Electronic controls are additionally protected with triple high-
sensitivity fuses located on the main board
.
+
Defective fuses must be replaced with fuses with
identical rating!
The LD6230 is a Class I device in which a low-Ohm protective
ground wire is an integral part of its safety design.
During the installation, make sure that a low-Ohm protective
conductor (< 0,1 Ohm) exists between all bare metal parts and
the grounding on the main connector.
3KDVH
&+
CH 2
&+
CH 4
&+
CH 6
L1
X
X
L2
X
X
L3
X
X
2XWSXWFKDQQHOV
* Activation of control electronics and respective output channel
CONNECTOR TERMINAL STRIP
The connector terminal strip of your LD6230 is laid out for
cables with diameters between 0.326 mm
2
(AWG 22) and
4 mm
2
(AWG 12). When using flexible access lines, cable end
contacts corresponding to manufacturer specifications have
to be used. To assure good contact, skin the cable endings
between 9 - 13 mm.
During the installation, all applicable national standards need
to be adhered to.
Illustration: LD6230 connector terminal strip
When your LD6230 leaves the assembly plant, all incoming
and outgoing neutral conductor connectors
are bridged.
The incoming phases L1/L1, L2/L2 and L3/L3
are always
connected to one another in pairs and switched to the overload
protection of the channels 1 to 6. They protect output connectors
E1 to E6
. Each of the channels can handle currents of
maximum 10 Amperes. The green-yellow conductors
(PE)
may only be used as protective conductors.
All manuals and user guides at all-guides.com
