background image

WARNING

Failure to follow these instructions and observe the 
warnings provided in this operations manual could result in 
fire, explosion or burn hazard, which could cause property 
damage, personal injury or death.

Gas vapour is highly explosive and can cause serious bodily 
injury or damage to property if allowed to accumulate in a 
confined space and ignited.

This appliance must not be installed under or on any 
combustible material. Minimum clearance from combustible 
materials to all sides of the appliance is 450mm (18”).

These instructions must be left with the owner.

NOTE:

1.     Do not use gas other than the type specified on the  

Data Plate.

2.     The appliance is designed for use by adults, keep 

children away from the barbecue at all times.

3.     Use only on a flat, level, stable non-combustible surface. 

Do not use this appliance on any surface that can burn 
or melt.

4.     When in use, gas cylinder should be kept at designated 

mountings of barbecue, and supply hoses kept away 
from any hot surfaces.

5.     To prevent accidental fires, before using the appliance 

ensure that there is no apparent damage to hose and 
regulator and all joint connections are in good order and 
not leaking.

6.     Use a soapy water solution on all joints in order to check 

for leaks. If bubbles appear, it indicates that there is a 
leak and the appliance must not be used.

7.     LPG cylinder, regulator and hose must comply with 

national standards.

8.     Do not move or attempt to move the appliance while in 

operation.

9     Do not operate this appliance before leak checking 

hoses and gas cylinder connection.

To the installer

•      For fixed installations, this appliance must be installed 

in accordance with local authority and any relevant 
statutory regulations.

•    For fixed installations, refer to relevant statutory    

  regulations for pipe sizing details.

•     Consult other trades. Where required, consult a 

bricklayer or an electrician for parts of the installation 
that could have an effect on these areas.

•     Allow a 20mm gap from back of barbecue body for 

ventilation and air access.

•     Test appliance for correct operation before leaving, and 

instruct user on its use.

•     If correct operation cannot be achieved, disconnect 

barbecue from gas supply, and contact your nearest 
BeefEater dealer.

•     Please only use BeefEater supplied hose(s) to connect 

this appliance. Natural Gas conversion kits are available 
from your nearest BeefEater dealer.

•     Australia only (applies to all gas types) : Where a mobile 

appliance is to be connected to a fixed gas supply via a 
flexible hose connection, a retaining tether of adequate 
strength shall be fixed to the appliance and be suitable 
to be fixed to the wall within 50mm of each connection 
point. The length of the tether shall not exceed 80% 
of the length of the hose assembly. In this way, if the 
barbecue is accidentally moved, the tether stops the 
barbecue from stretching the hose.

Do not

•      Lean over barbecue when lighting.

•      Leave cooking food unattended.

•      Delay lighting burners after turning gas on.

•      Spray or store aerosols in vicinity of barbecue whilst  

in operation.

•    Place articles on or against this appliance

•      Store combustible materials, gasoline or flammable 

liquids or vapours within 450mm (18”) of barbecue.

•      Use caustic based cleaning agents on the barbecue.

•      Operate barbecue with any cover on.

•      Use plastic or glass utensils on the barbecue.

•      Operate barbecue in strong winds.

•      Attempt to dismantle control valves.

•      Attempt to dismantle or adjust regulator.

•      Test for gas leaks with a naked flame.

•      Store gas cylinder indoors, or in any enclosed area.

•      Lay the gas cylinder down. Always keep it upright.

•      Use barbecue indoors.

•      Expose hose to direct sunlight.

IMPORTANT SAFETY INSTRUCTIONS

4

IMPORTANT SAFETY INSTRUCTIONS

Содержание 1600 Series





































Отзывы: