background image

29

CLEANING AND STORING YOUR BARBECUE

Cleaning Vitreous Enamel Surfaces and Barbecue  
Control Panel

Although porcelain enamel will keep its lustrous finish even 
under adverse conditions, it still needs regular cleaning. 
After the appliance has been used, wash down the surfaces 
with hot soapy water. Caustic cleaners should be avoided. 
For barbecues near the ocean or salt-water environment, 
more frequent cleaning and servicing should be conducted. 
Wash regularly, rinse and then dry before covering. (In a salt 
water or marine environment, more rapid deterioration can 
be expected which is not covered by warranty).

The cleaning and care instructions are essential for the 
proper functioning and operation of your appliance over time. 
Failure to adhere to these care instructions may affect your 
ability to make a claim under the manufacturer’s warranty.

Cleaning Plates and Grills

Many food acids, marinades, juices and sauces contain 
highly acidic elements that will slowly attack the surface of 
the plates and grills if not removed after cooking.

•  

After use, remove all solid material from the cooking 
surfaces using a brass bristle brush or plastic scourer. 
Brushes specifically designed for this purpose can 
be purchased from your BeefEater retailer. Wipe off 
remaining residue with a paper towel.

•  

Gently wash the surface of the grills with a soft sponge 
and a solution of hot water and a mild dishwashing 
liquid. Do not use highly caustic, harsh or abrasive 
chemical cleaners to clean the cooking grills. Always 
check the manufacturer’s recommendations for the 
cleaner prior to use.

•  

Coat the grills with a layer of cooking oil. This will help 
protect the surfaces between uses.

•  

For porcelain enamel coated cooking surfaces, do not 
use any metal tools to clean the surface. Use only  
a brass bristle wire brush to remove hard deposits.

Do not clean the cooking surfaces in a dishwashing machine. 
For hard deposits and heavy grease, do not use steel wool 
or metal scrapers. Use concentrated detergent or domestic 
cleaning powders.

Cleaning The Drip Tray

Never remove the grease tray while the barbecue is hot. 
Always remove and clean the grease tray after the unit has 
cooled down.

Replace aluminium foil on main drip tray (if used) and clean 
both waste trays at regular intervals to prevent grease build-
up, which could result in a grease fire and void the barbecue 
warranty.

Cleaning The Burners

•  

Check main opening, throat and venturi to each 
burner regularly for insect nests (eg. wasp, ants or 
spiders). Nests are dangerous and must be cleaned 
out thoroughly.

•  

Remove burners periodically and scrub clean with soapy 
water and a wire brush making sure that the ports are 
free of obstructions.

Replace burners in the correct position and dry by lighting 
each one to avoid subsequent corrosion.

A clogged burner can lead to a fire beneath the grill.

Storing Your Barbecue

When storing barbecue for extended periods, be certain all 
controls and cylinder valves are turned off. If storing the 
barbecue indoors remove gas cylinder and store the cylinder 
in a ventilated area outdoors.

Gas cylinders must be stored outdoors, out of reach of 
children and must not be stored in a building, garage or any 
other enclosed area.

The barbecue should be covered when not in use. eg a 
polyester or vinyl barbecue cover. Frequently check and 
tighten all nuts and bolts on the barbecue and trolley

The gas cylinder supply valve must be turned off when the 
appliance is not in use.

WARNING

Note: For storage and cylinder exchange, disconnect hose at 
the cylinder only, do not disconnect hose from appliance.

Please note that environmental conditions need to be taken 
into account with regards to the maintenance required on 
your product. In particular units installed in humid climates 
or seaside locations will be more susceptible to surface 
corrosion/discolouration over time. In these conditions 
Electrolux strongly recommends cleaning and drying your 
barbecue after every use and covering it when not in use to 
minimise exposure to the elements.

Main opening

Throat

CLEANING AND STORING YOU BARBECUE

Содержание 1600 Series





































Отзывы: