Beckhoff KL4414 Скачать руководство пользователя страница 30

Страница: 30 / 45

KS2000 Configuration Software

KL4414, KL4418, KL4424, KL4428

Version: 3.0.0

6.3

Settings

The dialog mask for parameterizing the KL4414 or KS4424 can be found under

Settings

Fig. 22: Settings via KS2000

Operation mode

•

User scaling active (

R32.0 [

}

40]

)

You can activate user scaling here (default: disabled).

•

Manufacturer scaling active (

You can deactivate manufacturer scaling here (default: enabled).

•

Watchdog timer active (

R32.2 [

}

40]

)

You can deactivate the watchdog timer here (default: enabled).

•

Signed amount representation (

R32.3 [

}

40]

)

Here you can enable the signed amount representation (default: disabled).

•

Signed representation active (

R32.5 [

}

40]

)

Here you can enable the signed representation (default: disabled).

•

User switch-on value active (

R32.8 [

}

40]

)

Here you can enable the user switch-on value (default: disabled).

Register data

•

User offset (

R33) [

}

40]

Here you can specify the user offset (default: 0).

•

User gain (

R34) [

}

40]

Here you can specify the user gain (default: 256).

•

User switch-on value (

R35 [

}

40]

)

Here you can specify the user switch-on value (default: 0).

Содержание KL4414














































Результаты поиска

Содержание KL4414

Отзывы:

Похожие инструкции для KL4414

Бренды по названию

Популярные бренды

Beckhoff KL4414, Документация

Результаты поиска

Содержание KL4414

Отзывы:

Похожие инструкции для KL4414

Бренды по названию

Популярные бренды