Beckhoff KL4011 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 19

Beckhoff KL4011 Скачать руководство пользователя страница 11

Register Description

KL401x and KL402x

9

R13: Data type register

Data type register

0x00

Terminal with no valid data type

0x01

Byte array

0x02

Structure 1 byte n bytes

0x03

Word array

0x04

Structure 1 byte n words

0x05

Double word array

0x06

Structure 1 byte n double words

0x07

Structure 1 byte 1 double word

0x08

Structure 1 byte 1 double word

0x11

Byte array with variable logical channel length

0x12

Structure 1 byte n bytes with variable logical channel
length (e.g. 60xx)

0x13

Word array with variable logical channel length

0x14

Structure 1 byte n words with variable logical channel
length

0x15

Double word array with variable logical channel length

0x16

Structure 1 byte n double words with variable logical
channel length

R14: reserved

R15: Alignment bits (RAM)
The alignment bits are used to place the analog terminal in the Bus
Coupler on a byte boundary.

Manufacturer parameters

R16 to R30: Manufacturer parameter area (SEEROM)

The manufacturer parameters are specific for each type of terminal. They
are programmed by the manufacturer, but can also be modified by the
controller. The manufacturer parameters are stored in a serial EEPROM in
the terminal, and are retained in the event of voltage drop-out.
These registers can only be altered after a code-word has been set in R31.

User parameters

R31 to R47: User parameter area (SEEROM)

The user parameters are specific for each type of terminal. They can be
modified by the programmer. The user parameters are stored in a serial
EEPROM in the terminal, and are retained in the event of voltage drop-out.
The user area is write-protected by a code-word.

i

Note

R31: Code-word register in RAM
The code-word 0x1235 must be entered here so that parameters in the
user area can be modified. If any other value is entered into this register,
the write-protection is active. When write protection is not active, the code
word is returned when the register is read. If the write protection is active,
the register contains a zero value.

R32: Feature register
This register specifies the terminal's operating modes. Thus, for instance, a
user-specific scaling can be activated for the analog I/Os.
R33 to R47 Terminal-specific Registers
The function of these registers depends on the respective terminal type
(see terminal-specific register description).

Extended application region

R47 to R63

Extended registers with additional functions.

«
...
9
10
11
12
13
...
»

Содержание KL4011




















Отзывы:

Нет отзывов