Beckhoff EP9224-0037 Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 64

background image

Mounting and cabling

EP9224-0037

17

Version: 1.0

3.1.2

Mounting

Mount EtherCAT Box modules with two M4 screws in the centrally located fixing holes.

The screws must be longer than 15 mm. The fastening holes in the modules have no thread.

Protect connectors against soiling

Protect all module connections from soiling during installation! The protection classes IP65, IP66,
IP67 (in accordance with EN 60529) are ensured only if all connectors are wired or sealed! Unused
connectors must be sealed with suitable protective caps (see Beckhoff catalog for connector sets
and protective caps)!

Cooling plate

The EP9224-0037 module has a cooling plate on the underside. For the effective dissipation of the
resultant power loss, the box must be bolted to a metal base, e.g. the machine bed, if possible mak-
ing contact over the entire surface. A temperature-related automatic switch-off of the box can occur
if care is not taken to ensure that the power loss from the module is dissipated via the cooling plate.
A corresponding temperature error bit is then set!

Note when mounting that the overall height is increased further by the fieldbus connections. See chapter
Accessories.

3.1.3

Connector

M8 connector: X52, X53, X54, X55

Screw M8 connectors tight with a torque wrench. (e.g. ZB8801 from Beckhoff)
Torque: 0.4 Nm.

B17 connector: X70, X71

Screw B17 connectors tight by hand:
Plug the cable connector into the connector on the box to the stop. Turn the cap nuts of the cable connector
clockwise by about 1/8 of a turn to the stop.

«
...
15
16
17
18
19
...
»

Содержание EP9224-0037

































































Отзывы:

Нет отзывов

Похожие инструкции для EP9224-0037

iBootBar iBB-N15

Бренд: Dataprobe Страницы: 37

Бренд: Baumuller Страницы: 72

Бренд: Panamax Страницы: 1

2 IP PDU ETH 53R14

Бренд: NetPing Страницы: 41

Бренд: Arcteq Страницы: 455

RELION 650 SERIES

Бренд: ABB Страницы: 68

Бренд: Ayre Страницы: 2

Бренд: RCI Страницы: 4

Бренд: Portawattz Страницы: 32

DC Power Distribution Module 48212-DC

Бренд: Leviton Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды