Beckhoff C6925 Скачать руководство пользователя

Страница: 15 / 47

Product overview

C6925

Version: 2.1

3.4

Status LEDs

The Industrial PC has either three or seven status LEDs, depending on the device generation. The following
table shows how many LEDs exist in each generation:

Table 9: Device generation status LEDs

Generation

Number of status LEDs

C6925-0020

PWR, FB, HDD

C6925-0030

PWR, FB, HDD

C6925-0040

PWR, TC, IDE, FAN, USR, FB RUN, FB ERR

The LEDs provide information on the following aspects:

• the status of the power controller (PWR)

• the TwinCAT status (TC)

• the hard disk activity (IDE/HDD)

• the fan status (FAN)

• the user (USR)

• the fieldbus activity (FB RUN)

• the fieldbus status (FB, FB ERR)

The figure shows where the LEDs are located on the Industrial PC.

Fig. 7: C6925 Status LEDs

Table 10: Meaning of the Status LEDs

LED

Color/flashing interval

Meaning

PWR (Power)

green

off

Computer on

Computer off

FB (fieldbus)

red

blue

blue/red flashing

green

green/red flashing

TwinCAT Stop

TwinCAT Config

TwinCAT Config (fieldbus error)

TwinCAT Run

TwinCAT Run (fieldbus error)

HDD (hard disk)

red

Accessing storage media

Содержание C6925
















































Результаты поиска

Содержание C6925

Отзывы:

Похожие инструкции для C6925

Бренды по названию

Популярные бренды

Beckhoff C6925, Руководство пользователя

Результаты поиска

Содержание C6925

Отзывы:

Похожие инструкции для C6925

Бренды по названию

Популярные бренды