Becker P5-B01, Руководство по сборке и эксплуатации, Страница: 4 / 20

Safety instructions
The following safety instructions and warnings are intended to avert hazards and to prevent property damage and personal injury.
Instructions for the user
General information
•
All work, including maintenance and cleaning, on electrical installations as well as other system parts must always be performed
by authorised specialists, in particular qualified electricians.
•
Children from the age of 8 years and persons with reduced physical, sensory or mental capabilities or lack of experience and/or
knowledge may use these devices, provided they are supervised or have been instructed in the safe use of the device, and have
understood the hazards involved. Children must not play with the device.
•
Systems have to be checked regularly by authorised specialists for wear and damage.
• Always put damaged systems out of operation immediately until they are repaired by an authorised specialist.
• Do not operate equipment if people or objects are within the danger zone.
•
Observe the danger zone of the equipment during operation.
• Stop and disconnect the equipment from the mains power supply when maintenance and cleaning is being performed either on
the system itself or in the immediate vicinity of it.
• Ensure that there is adequate clearance (at least 40 cm) between moving parts and adjacent objects.
Caution
Safety instructions for avoiding serious injuries.
• Crushing or shearing points must be avoided or protected.
Instructions for installation and commissioning
General information
•
Observe the safety instructions in EN 60335-2-97. Please note that this list of safety instructions is not exhaustive, since it would
be impossible for the standard to include all sources of danger. For example, the design of the operated product, the way the
drive works in the situation it is installed in or even the way the end product is mounted in the end user’s place of use cannot be
taken into consideration by the drive manufacturer.
If any questions or uncertainties regarding the safety instructions contained in the standard arise, please contact the manufac-
turer of the part or end product in question.
• All applicable standards and regulations for electrical installation must be complied with.
• All work, including maintenance and cleaning, on electrical installations as well as other system parts must always be performed
by authorised specialists, in particular qualified electricians.
• Only use spare parts, tools and accessory devices which have been approved by the drive manufacturer.
Unapproved third-party products or modifications to the system and its accessories represent a risk to your safety and the
safety of others. This means that the use of unapproved third-party products, or modifications which have not been agreed with
or approved by us, are prohibited. We do not accept liability for damage or injury arising from such actions.
•
Position control devices within sight of the driven product, but away from moving parts, at a height of over 1.5 m.
• Permanently mounted control devices must be positioned where they can be seen.
• Rated torque and duty cycle must be suitable for the requirements of the driven product.
Technical data – rated torque and service life can be found on the type plate of the tubular drive.
• Moving parts of drives must be installed at a height of over 2.5 m above floor level or any other surface from which access to the
drive is gained.
• To ensure safe operation of the system after commissioning, the limit positions must be correctly set/programmed in.
• Drives with a H05VV-F connecting cable may only be used indoors.
•
Drives with a H05RR-F, S05RN-F or 05RN-F connecting cable may be used both indoors and outdoors.
• To connect the drive to the driven part, solely mechanical accessory components made by the drive manufacturer from the cur-
rent product catalogue may be used. The components must be installed in accordance with the manufacturer's instructions.
•
If the drive is used for shading solutions in a specially marked area (e.g. escape routes, hazard zones, safety areas), compliance
with all applicable regulations and standards must be ensured.
Caution
Safety instructions for avoiding serious injuries.
•
When electrical or electronic equipment and units are operated, certain components, e.g., the power supply
unit, are live. Physical injuries or damage to property can result in the event of unauthorised interventions or
failure to heed warnings.
• Be careful when touching the tubular drive, as it heats up during operation for technological reasons.
•
Before installation, shut down all lines and control devices that are not essential for operation.
4