Becker HPP-SB Скачать руководство пользователя | Manualshive

Страница: 15 / 26

background image

HPP-SB Positioner

Assembly

HPP-SB

15

September 1999

7. Center the posts in bodies (F&G) by:

a. Rotating the diaphragm assemblies (from

Step 5

) counterclockwise until they stop (Ž) .

b. Marking the diaphragms and bodies (F&G) with a single line.
c. Rotating the diaphragm assemblies clockwise until they stop (ŽŽŽ).
d. Marking bodies (F&G) with extensions from the lines on the diaphragms.
e. Center the line on the diaphragm between the two lines on each body (ŽŽ).

8. Keeping the diaphragms securely in the center, between the inscribed lines, fasten sensitivity

spacer (V) to top and bottom bodies (F&G) with twelve 1/4-20 x 3/4" HHCS (W). This will pre-
vent the diaphragm assemblies from moving.

NOTE:

Align numbers stamped on the positioner parts in numerical order.

HPP-SB Positioner

Assembly

HPP-SB

15

September 1999

«
...
13
14
15
16
17
...
»

Содержание HPP-SB



























Отзывы:

Нет отзывов

Похожие инструкции для HPP-SB

Бренд: ABB Страницы: 48

PCV F200-B17-V1D Series

Бренд: Pepperl+Fuchs Страницы: 35

Logix 520si Series

Бренд: Flowserve Страницы: 20

Бренд: halstrup-walcher Страницы: 8

Бренд: Armada Technologies Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды