Becker HPP-SB Скачать руководство пользователя | Manualshive

Страница: 14 / 26

background image

HPP-SB Positioner

Assembly

HPP-SB

14

September 1999

5. Slide one grooved washer (O) onto

each piston with the grooves facing
away from the valve body.

5a.Install convoluted diaphragms (R) onto

the washers (O) as shown.

5b. Install another washer (O) onto each

piston with grooves facing the dia-
phragms.

5c. Secure the diaphragm assemblies by

threading the 1/2-20 hex jam nuts (S)
onto the inside piston of top body (G)
and the outside piston of bottom body
(F).

5d. Install special flat nut (Q) onto the in-

side piston of bottom body (F) and spe-
cial spring nut (P) onto the outside pis-
ton of top body (G).

5e. Torque all nuts (S,Q,P) to 95-100 in-

lbs.

6a. Press fit thrust bearing (U) into the ad-

justing drum with the stamped letters'
side first (this will place the bearing
case inside the drum with the bearing
surface freely rotating).

6b. Install the adjusting drum to inside pis-

ton (L) of top body (G) by threading the
drum until it touches the 1/2-20 hex jam
nut.

HPP-SB Positioner

Assembly

HPP-SB

14

September 1999

«
...
12
13
14
15
16
...
»

Содержание HPP-SB



























Отзывы:

Нет отзывов

Похожие инструкции для HPP-SB

Бренд: Parker Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды