Beastx MICROBEAST PLUS Скачать руководство пользователя страница 319 | Manualshive

Страница: 319 / 353

Beastx MICROBEAST PLUS Скачать руководство пользователя страница 319

130 BLE2SYS Conﬁguration

When using an iOS or Android smartphone/tablet you can conﬁgure the BLE2SYS
device by tapping the BLE2SYS button on top of the main window.

This will open

a conﬁguration screen (or you will be asked to enter the pin code for the bluetooth
device ﬁrst).

Also you can conﬁgure your BLE2SYS by the help of a PC/mac.

In

this case you have to connect the BLE2SYS to a USB2SYS computer interface using a
Y-harness and powering with a receiver battery over the second line (as shown earlier

).

Then just click ”Connect” and open the com port as you would connect to a BEASTX gyro.

130.1 Device Name

You can set a custom device name (maximum length 11 digits) by changing the name in
the line on top of the screen, i. e. by entering the name of your helicopter. Then this
name will be the bluetooth identiﬁer. Please note when chaging the name you may have
to restart the StudioX app as well as the BLE2SYS device in order to see the new name in
the main window.

130.2 Automatic deactivation

Never ever ﬂy your helicopter when the bluetooth device is active! The bluetooth signal is
sent on the 2.4GHz band and may interfer with your radio signal. For your convenience you
can set an automatic deactivation timeout here, so the device will power oﬀ automatically
after the given amount of time when no connection is requested. So you can leave the
module plugged into your BEASTX device when ﬂying the helicopter and when not using
the app. When you set the timeout to 0 the device will be active all time.

Warning:

When you deactivate the timeout, never leave your BLE2SYS connected

when ﬂying your helicopter! This can lead to radio signal loss and cause severe injury
or damage!

1

https://wiki.beastx.com/./index.php/StudioXm/en

311

«
...
317
318
319
320
321
...
»

Содержание MICROBEAST PLUS


































































































































































































































































































































































Отзывы:

Нет отзывов