Beastx MICROBEAST PLUS Скачать руководство пользователя страница 318 | Manualshive

Страница: 318 / 353

Beastx MICROBEAST PLUS Скачать руководство пользователя страница 318

BEASTX ﬂybarless system

can be helpful to close the app completely, disconnect and reconnect the
BLE2SYS and start over again!

Also note that the device name can be diﬀerent! By default it's ”BLE2SYS”, but as it's
possible to change the bluetooth id, it maybe diﬀerent. (The automatic deactivation
time as well as the bluetooth id can be changed in the conﬁguration menu by clicking
the BLE2SYS button above the device selection box.)

129.2 Overview screen

When connection to your BEASTX device is established, wait until the data is loaded from
the device and initialization sequence is ﬁnished. At ﬁrst the system will calibrate to the
radio system, Menu LEDs H to N will cycle up and down at the device (MICROBEAST
PLUS/AR7210BX) and you can read

Radio init

in the opening overview screen. During

this time

do not move the sticks on your radio

as the system is learning the stick

mid positions! In the second step the device checks if the sensors are working correctly
and learns the sensor rest positions. Here Menu LEDs A to G will cycle up and down
(MICROBEAST PLUS/AR7210BX) and you can read

Sensor init

in the opening

overview screen. During this time

do not move the helicopter!

When initialization is

completed, the Status LED will change to blue or purple color indicating the current gyro
mode and you can read the gyro gain and mode in the app.

To be able to access all settings wait until your device has passed initialization sequence.
If it doesn't, probably receiver setting is wrong. So start with the CONTROL SETUP.

If you can't get through the initialization sequence either because LEDs A-G or LEDs
H-N don't stop cycling, please read the FAQ

and do the CONTROL SETUP ﬁrst (see

manual of your device for further instructions).

2

https://wiki.beastx.com/./index.php/Help:FAQ:Powerup/en

310

«
...
316
317
318
319
320
...
»

Содержание MICROBEAST PLUS


































































































































































































































































































































































Отзывы:

Нет отзывов