E
R
L
A
U
B
T
Z
E
R
T I
F I Z
I E R U N G
N
A
C
H
EN 1
600
5
E
N
A
B L E
S
A C C
O R
D
A
N
C
E
W
I
T
H
E
R
L
A
U
B
T
Z
E
R
T I
F I Z
I E R U N G
N
A
C
H
DIN 1
865
0
E
N
A
B L E
S
A C C
O R
D
A
N
C
E
W
I
T
H
BEA SA | LIEGE Science Park | ALLÉE DES NOISETIERS 5 - 4031 ANGLEUR [BELGIUM] | T +32 4 361 65 65 | F +32 4 361 28 58 | [email protected] | WWW.BEA-SENSORS.COM
©
B
EA
|
O
ri
gi
na
l i
ns
tr
uc
ti
on
s
|
4
2
.8
32
6 / V
3
- 11
.1
7
BEA hereby declares that the IXIO-DP3 is in conformity with the basic requirements and the other relevant provisions of the directives
2014/53/EU, 2006/95/CE and 2006/42/EC.
Notified Body for EC-type inspection: 0044 - TÜV NORD CERT GmbH, Langemarckstr. 20, D-45141 Essen
EC-type examination certificate number: 44 205 13089612
Angleur, September 2017
Pierre Gardier, authorized representative and responsible for technical documentation
The complete declaration of conformity is available on our website
Only for EC countries: According to the European Guideline 2012/19/EU for Waste Electrical and Electronic Equipment (WEEE)
TECHNICAL SPECIFICATIONS
Supply voltage:
Power consumption:
Mounting height:
Temperature range:
Degree of protection:
Noise:
Expected lifetime:
Applicable directives:
Presence
Typical response time: < 200 ms (max. 500 ms)
Active infrared with background analysis
Spot: 5 cm x 5 cm (typ)
Number of spots: max. 24 per curtain
Number of curtains: 2
Input:
Pulse polarity: positive or negative (adjustable)
Impedance:
- Positive pulse: 2 K to ground
- Negative pulse: 470 R to + sensor power supply
Pulse voltage: 6 V to 30 V
Pulse duration: 4 µs to 500 µs
Duty cycle: max. 50%
Output:
Pulse polarity: negative
Level:
- Standby: Pulse from V to ground
- Detection: V Supply
Topology: op-collector with 4.7 K to 3.3 V
Max. sink current: 25 mA with external 1 K to 24 V
EN 12978
EN ISO 13849-1 PL «c» CAT. 2
(under the condition that the door control system monitors
the sensor at least once per door cycle)
IEC 61496-1 ESPE Type 2
EN 16005 Chapter 4.6.8;
DIN 18650-1 Chapter 5.7.4
BS 7036-1 Chapter 8.1
Motion
Min. detection speed: 5 cm/s
Microwave doppler radar
Transmitter frequency: 24.150 GHz
Transmitter radiated power: < 20 dBm EIRP
Transmitter power density: < 5 mW/cm
2
Solid-state-relay (potential and polarity free)
Max. contact current: 100 mA
Max. contact voltage: 42 V AC/DC
- in switching mode: NO/NC
- in frequency mode: pulsed signal
(f= 100 Hz +/- 10%)
Galvanically isolated current source
No detection: current source ON
Open circuit voltage: 6.5 V
Output voltage available at 10 mA: 3 V min.
Typical load: up to 3 optocouplers in series
Detection: current source OFF
Open-circuit remained voltage: < 500 mV
EN 12978
EN ISO 13849-1 PL «d» CAT. 2
EN 16005 Chapter 4.6.8;
DIN 18650-1 Chapter 5.7.4; AutSchR
BS 7036-1:1996 Chapter 7.3.2
(only applicable for relay output in frequency mode
and current source output)
Detection mode:
Technology:
Output:
Norm conformity:
Specifications are subject to changes without prior notice.
All values measured in specific conditions and with a temperature of 25°C.
12 V - 30 V DC +/-10%
(to be operated from SELV compatible power supplies only)
< 2.5 W
2 m to 3.5 m
(according to the applicable laws and regulations)
-25°C to +55°C; 0-95% relative humidity, non condensing
IP54
< 70 dB
20 years
RED 2014/53/EU; MD 2006/42/EC; ROHS 2 2011/65/EU
PL
EA
SE K
EE
P F
O
R F
U
R
TH
ER U
SE - D
ES
IG
N
ED F
O
R C
O
LO
U
R P
R
IN
TI
N
G
