Be Next-iHome Panic Watch EU Скачать руководство пользователя страница 5

 

Version 0.2 

31 July 2013 

www.iHome.eu

 

* if a size is other then given size the frame is ignored totally so configuration values are 

not

 changed  

 

class: 0x85 COMMAND_CLASS_ASSOCIATION 

The Association Command Class is used to associate other devices with the 

Panic Watch

. The devices that are 

associated can be controlled on application level.  
 
The 

Panic Watch

 can be associated into a grouping. If so, the 

Panic Watch

 can control other Z-Wave device 

(does not have to be a controller).  
 
The Panic Watch has 2 association groups 
 
Group 1 

Maximum supported nodes: 8 
 

If configuration parameter 4 configured with value 0 then this group is used  

-

 

SOS button: send ALARM_REPORT. 

 
If configuration parameter 4 configured with value other then 0 (1-255) then this group is used  

-

 

SOS button: send BASIC_SET, 0xFF. 

Group 2 

Maximum supported nodes: 8 

 
Not used on application 
 

Class: 0x80 COMMAND_CLASS_BATTERY 

This class is used to request and report battery levels for a given device. 
When battery level is lower then 20% the Panic Watch will send a battery warning (value 255) after every wake 
up notification. A battery get will report the actual value even if below 20 %. 
 
When the batteries are placed a unsolicited battery report is sent (when included).  
 

class: 0x84 COMMAND_CLASS_WAKE_UP 

The Wake Up Command Class is used at battery-operated devices. This class allows the 

Panic Watch

 to wake 

up occasionally to notify others devices, that the 

Panic Watch

 is ready to receive commands. After receiving 

the commands the 

Panic Watch

 will go into sleep mode again. The wake up interval can be set using the 

WAKE_UP_INTERVAL_SET command.  
 
The default value is 0x15180 = 86400 sec = 24 hour 
The default node is 0xFF = 255 (broadcast) 
 
It is possible to send a 

wake up notification 

on user interaction. To do this press and hold the Panic Watch for 

11 seconds. Ignore the blinking of the led and keep the button pressed for at least 15 seconds. 
 
It is possible to send a 

wake up notification 

on user interaction. To do this press and hold the Panic Watch for4 

seconds.  

Содержание Panic Watch EU










Отзывы: