background image

 

 

Fitting  your  Deville  onto  your  bike  requires  care  and  attention.  For  your  safety,  please  follow  these 
instructions. 

1.1

 

Steer tube 

Before  cutting  the  steer  tube,  first  take  some  measurements  taking  into  account  the  total  height  of  the 
headset, the length of the frame’s head tube, the height of the stem, then add 5 to 10mm. 
 
Calculate the length as below: 
Length of the head tube of the frame + height of the complete h height of the stem + 5 to 10mm. 

 b

 

Never  attempt  to  remove  or  replace  the  steer  tube  or  stanchions  independently  from  the  crown. 
Modifying  the  integrated  crown,  steer  tube,  or  stanchions  can  cause  an  assembly  failure.  It  is 
mandatory to replace the complete assembly for important safety reasons. 

1.2 Installing the front wheel 

To assemble the front wheel, follow this procedure: 
 

1.

 

Release the pinch bolt on right side of the fork (1). 

2.

 

Unscrew the axle (2) and remove it. 

3.

 

Install the wheel. 

4.

 

Insert the axle and screw it completely until it stops, do not overtighten. 

5.

 

Screw the axle pinch bolt to lock the axle (Torque between 4 and 4,5 Nm). 

 

To disassemble the wheel, follow these instructions in reverse. 

 

1.3. Brake caliper installation 

The Deville brake caliper bolt pattern uses PostMount 180 standard (PM180).  
To assemble the disc brakes, follow this procedure: 

1.

 

Install the disc brake caliper, according to disc brake manufacturer's specifications. 

2.

 

Be  sure  to  torque  all  fasteners  and  bolts  to  manufacturer's  recommendations.  Consult  the 
instructions that came with your disc brakes for proper installation procedures. It is recommended 
to install new brake pads, to ensure proper alignment. 

3.

 

Route the disc brake hose or cable housing from the caliper to the inside of the lower leg and through 
the supplied disc brake hose guide. 

4.

 

Test the brakes for proper operation on ground level before hitting the trails. 

 

The disc brake caliper mounting bolts must have 10 mm of thread engagement with the fork. 
The disc brake caliper mounting bolt tightening torque level must never exceed 10 nm

(2) 

(1) 

ASSEMBLY 

Содержание DEVILLE II













Отзывы: