6
5
Sensor Configuration
Without addressing:
Parameter
Step 1
Step 2
Field size
Functionality
Field geometry
Press [<] briefly
Press [>] briefly
Press [<] and [>] briefly at the same time
Frequency of the flashing
green LED (1-9 times) indicates
the current parameter level
5.1
Configuration with keys
Note:
If no key is actuated for 25 s, the programming mode is automatically exited –
however the sensor is still in the configuration mode. The settings made up to
that point are saved.
The status query is to find out what parameters have been set.
5.1.1
Status query with keys
5.2.2
Mode of operation
5.2
Configuration with remote control
A
c
tivation:
–Automatically after the sensor is connected to the supply
voltage
or
–Briefly disconnect the sensor from the supply voltage
or
–Press either key [<] or [>] on the sensor
Exiting:
–Press key combination
or
–Automatically after 30 min.
Note:
If no entry is made for 30 s, the connection is ended. The settings
made up to that point are saved.
1, 2, 3 small
4, 5, 6* medium
7, 8, 9
large
for Merkur version with direction recognition
Level
1*
forwards, mounting height standard
2
forwards, mounting height high
3
backwards, mounting height standard
4
backwards, mounting height high
5
direction recognition OFF, mounting height standard
6
direction recognition OFF, mounting height high
7
fo MTO, mounting height standard (MTO, see chap. 7)
8
fo MTO, mounting height high (MTO, see chap. 7)
1
narrow field
2*
wide field
Changing the functionality from level 6 to level 2:
1) Keep [<] and [>] pressed for 4 s, the green LED blinks once after 2 s,
once again after 4 s
2) Green LED flashes 6 times and thereby indicates the current parameter level
3) Press the key [<] four times in a row to decrease the parameter level
(green LED flashes twice and indicates the new parameter level)
4) Press [<] and [>] at the same time
The data transmission to and from the sensor is ensured by an IR interface. The
connection between the remote control and the sensor can only be established
when the sensor is in configuration mode.
The sensor can be configured in two ways:
→
With keys on the sensor (basic settings)
→
With the remote control (complete setting options)
With addressing:
1.
Press the start key
1.
Cover the IR interface of the
remote control with your hand
2.
Press the start key
→
flashes
3.
Release the IR interface
(remove hand)
4.
Press the corresponding numerical
key ( to )
– G and one of the keys 1 to 4 light up:
Connection successfully established
– G flashes:
Connection not established
→
Activate configuration mode
→
Hold remote control closer to the sensor and point directly at it
→
Check batteries in remote control
– No keys light up
→
Check/replace batteries in remote control
5.2.3
Setting / changing parameters
Keep the door open manually for 15 min. when making settings.
Afterwards, the door will close if no object is in the detection area
Door closes when no object is in the detection area, afterwards
standard operation
Configuration mode is ended, door closes when no object is in the
detection area, afterwards standard operation
After the connection has been successfully established, the parameters of the
sensor can be changed.
* Fa
c
tory setting
General procedure
[>]
[<]
Changing the field size: Press [<] and [>] for 2 s
Changing the functionality: Press [<] and [>] for 4 s
for Merkur version without direction recognition
1*
mounting height standard
2
mounting height high
Changing the field geometry:Press [<] and [>] for 6 s
Example
Restore factory settings: Press [<] and [>] for 8 s
Configuration mode
+
A
3
Establishing the connection
Each sensor can be assigned an address (1*, 2, 3 or 4). Different addresses are
necessary when several sensors are within the range of a remote control.
Address 1*
Address 2
Address 3
Address 4
5.2.1
Sensor addressing
G
G
G
1
4
+
A
1
+
A
2
+
A
3
Numerical keys to
1
9
IR interface (infrared)
Control keys to
A
F
Start
G
1) Keep [<] and [>] pressed for a corresponding length of time, every 2 s the
green LED will flash once
2) Frequency of the flashing green LED (1–9 times) indicates current parameter level
3) The parameter level can be decreased or increased with [<] and [>]
respectively
4) Press [<] and [>] briefly to exit the programming mode (settings are saved)
Level
Level
Level
