background image

TOYOTA FJ 

CRUISER 

 

      

     

Care must be taken when installing this accessory to ensure damage does not occur to the vehicle.  The installation of this 
accessory should follow approved guidelines to ensure a quality installation. 
 
These guidelines can be found in the "Accessory Installation Practices" document. 
 
This document covers such items as:- 

 

Vehicle Protection (use of covers and blankets, cleaning chemicals, etc.). 

 

Safety (eye protection, rechecking torque procedure, etc.). 

 

Vehicle Disassembly/Reassembly (panel removal, part storage, etc.). 

 

Electrical Component Disassembly/Reassembly (battery disconnection, connector removal, etc.). 

 
Please see your Toyota dealer for a copy of this document. 

1.

 

Pre-installation Precautions 

(a)

 

Use Seat & Floor Protectors and Fender 

Covers/Blankets to avoid damage to 

surfaces.  Operator Safety Warning (if 

applicable.) 

 

 

 

2.

 

Battery Disconnect 

(a)

 

NOTE: Be sure to open the rear hatch, 

PRIOR to disconnecting the battery. 

(b)

 

Remove the NEGATIVE (-) battery 

terminal using a 10mm socket before any 

disassembly starts.  (Fig. 2-1). 

3.

 

Disassemble Center Rear Storage Area 

(a)

 

Remove Cargo Net Cleats using 10mm 

Socket.  Place in a safe location. 

(b)

 

Remove Side Trim Cover, Quarter Trim 

Pocket, Quarter Trim Pocket Tray. (Fig. 

3-2) 

 

 

 

 

 

 

Fig 2-1 

Fig 3-2 

 

STOP

 

STOP

 

STOP

 

Southeast Toyota Distributors, LLC

Page 2 of 9

Содержание BASE TUBE










Отзывы: