baxter Auto Syringe AS50 Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 100

baxter Auto Syringe AS50 Скачать руководство пользователя страница 72

Configuration

Page 66

Auto Syringe AS50 Infusion Pump Operator’s Manual

07-19-B3-430

Idle Alarm

This option enables the pump to issue a continuous audible alarm when a

PUMP IS IDLE

condition occurs. If the option is disabled, the pump beeps 15 times at two minute
intervals when a

PUMP IS IDLE

condition occurs.

Near End Alert (NEAR END)

This option enables the pump to issue an alert during an infusion prior to an expected

VOL LIMIT

or

EMPTY

alarm. The option specifies the number of minutes prior to the alarm

that the expected alert will be issued and the number of beeps in the alert.

The form of a Near End alert display is

xx

MIN VOL LIM

,

xx

MIN EMPTY

or

xx

MIN

(protocol).

The value

xx

is the configured number of minutes. The first and second forms apply to

impending

VOLUME LIMIT

or

EMPTY

conditions when no protocol has been selected. The

third form applies to either condition when a protocol has been selected. Press

CONFIRM

to view the current settings.

Note:

When an infusion is started, no

NEAR END

alert will occur if fewer than the config-

ured number of minutes remain before an

EMPTY

or

VOL LIMIT

alarm is due to

occur. For example, if the

NEAR END

alert is configured for 10 minutes and 9 min-

utes remains before the volume limit is reached, no

NEAR END

alert will occur

when

START

is pressed.

Bolus Complete Alert (BOLUS COMPLETE)

This option enables the pump to issue an alert when a bolus completes.

Dose Complete Alarm (DOSE COMPLETE)

This option enables the pump to issue an alarm when a dose completes in SINGLE
DOSE mode.

Volume Limit Alarm (VOLUME LIMIT)

This option applies to mL/hr and mL/min modes only. During initial programming, the
pump prompts the operator to enter a volume limit value in mL. The Volume Limit feature
triggers an alarm after the pump has delivered the pre-programmed volume of drug. With
this option enabled, a

NEAR END

alert is issued when the Volume Limit will be reached

within a preconfigured time period at the current rate of infusion. See “Near End Alert” on
page 66.

Identifier

The Identifier is not a configuration group, but is included here for reference purposes.
The Identifier is a short message (up to eight characters) that is displayed for three
seconds following the Lamp Test. The Identifier can be created or edited during the pump
configuration process.

«
...
70
71
72
73
74
...
»

Содержание Auto Syringe AS50





































































































Отзывы:

Нет отзывов