baxter Auto Syringe AS50 Скачать руководство пользователя страница 65 | Manualshive

Страница: 65 / 100

baxter Auto Syringe AS50 Скачать руководство пользователя страница 65

07-19-B3-430

Auto Syringe AS50 Infusion Pump Operator’s Manual

Page 59

Additional Functions and Operations

●

If the syringe is improperly mounted, the pump displays one of the following alert or
alarm messages:

CHECK BARREL

,

CHECK FLANGE

, or

CHECK PLUNGER

. Examine

the syringe and correct the indicated problem.

If a combination of such conditions is sensed, the pump displays a

CHECK SYRINGE

alert or alarm message instead.

Lock and Auto Lock Functions

The Lock function serves two purposes. First, it reduces risk of accidental key activations
by disabling all keys except

LOCK

. Second, the Lock function makes it convenient to

program the pump in advance of delivery by disabling the audio portion of the

PUMP IS

IDLE

alert or alarm.

The Lock function is activated by pressing

LOCK

. Pressing

LOCK

again restores normal

operation. The

LOCK

light remains on while the Lock function is active.

Note:

The pump will not allow the Lock function to be active during a

LINE OCCLUDED

alarm condition.

The Auto Lock feature can be enabled through pump configuration. During an infusion,
the Auto Lock feature automatically sets the Lock function two minutes after the last key is
pressed. This feature is available only while the pump is in Run state.

If the pump enters Standby State because of an alarm condition, the keypad is
automatically unlocked.

The Total Delivered Display

The Total Delivered display indicates the accumulated total volume (in mL) that has been
delivered. Some infusion modes also show the total delivery in other units, such as mcg,
mg, or grams.

The Total Delivered display cannot be programmed, but can be cleared (reset to zero). To
clear the total delivered information, press

▲

or

▼

to move to the

TOTAL

m

L

field. The

annunciators will flash, then press

EDIT

and

CLR

to clear the display. After resetting the

Total Delivered display to zero, the previous value cannot be restored.

TOTAL

T

T

mL

TOTAL

T

T

mgrams
mLmcg

«
...
63
64
65
66
67
...
»

Содержание Auto Syringe AS50





































































































Отзывы:

Нет отзывов