manualshive.com logo in svg

Baxi PRIME HT 1.120, Инструкции для установщиков и пользователей, Страница: 10 / 40

Поделиться
Скачать
Baxi PRIME HT 1.120 Скачать руководство пользователя страница 10

10

INSTRUCTIONS FOR THE INSTALLER

Figure 6

0402_2506

Decide upon the boiler location, then tape the template on the wall.
Connect the pipework to the gas and water inlets prearranged on the template lower bar.
If you are either installing the boiler on a pre-existent system or substituting it, we suggest you also fit settling tanks on 
the system return pipework and under the boiler to collect the deposits and scaling which may remain and be circulated 
in the system after the purge.
When the boiler is fixed on the template connect the flue and air ducts (fittings supplied by the manufacturer) according 
to the instructions given in the following sections.
Connect the condensate outlet to the siphon supplied with the boiler. Connect the siphon to a drain, making sure there is 
a continuous slope. Horizontal sections must be avoided.

11. BOILER INSTALLATION

12. BOILER SIZE

0505_2001

Figure 5

9912220300

BOILER WIDTH 450

BOILER CONNECTION POINTS

BOILER HEIGHT

 780

021

1_2203

PRIME HT 1.280 - HT 1.240 - HT 1.120

PRIME HT 330 - HT 280 - HT 240

MR:  

G3/4 heating flow

US:  

G1/2 domestic hot water outlet

GAS:  

G3/4 gas inlet to the boiler

ES:   

G1/2

 

cold water inlet

RR:  

G3/4 heating return

SC:  

condensate drain

MR:  

G3/4 heating flow

US:  

G3/4 domestic hot water boiler 
delivery

GAS:  

G3/4 gas inlet to the boiler

ES:  

G1/2 cold water inlet

RR:  

G3/4 heating return

SC: 

condensate drain

Содержание PRIME HT 1.120









































Отзывы:

Нет отзывов