background image

MAINTENANCE

Battery replacement.

The igniter unit uses a 9V PP3 battery. To replace the
battery remove the firefront casting / front cover
casting. 
1. Remove and discard the battery from the ignition
block located below the burner tray at the left side. 
2. Fit the replacement battery to the ignition block.
(See figure 11). The positive terminal (+) is to the top
as you insert.
3. Replace the firefront casting /front cover casting.

Regular maintenance.

In order to achieve and maintain high levels of personal safety and performance
efficiency, it is essential that the opening at the back of the fire and the flue are kept
clear of any form of obstruction. It is possible that deposits of mortar or soot could fall
and accumulate causing the flue to be blocked or restricted and so preventing proper
clearance of dangerous exhaust fumes.
In the United Kingdom it is the law that a landlord must have any gas appliance, flue
and pipework which is situated in a tenant’s premises checked for safety at least every
twelve months by a competent person (In the U.K, a CORGI registered installer).
We recommend that all gas appliances and their flues, wherever situated, are checked
annually.

Servicing.

If you require your fire to be serviced, please contact British Gas or Scottish Gas

TELEPHONE 0845 950 0400 

and please quote the following details which can be

found on a ‘swing’ plate located below the burner behind the bottom hearth casting

a) Model and G.C. number.
b) Serial Number (To be found on a ‘swing’ plate located below the burner and
behind the bottom front cover). 

If you wish to replace any of the owner replaceable parts listed below please quote

the part number shown below.

Page 11

OWNER GUIDE

Figure 11. Fitting the battery

Содержание Classic 2 719













Отзывы: