Baumer EAL580 MT Series Скачать руководство пользователя страница 10

Страница: 10 / 74

Baumer_EAx_PROFINET_EN_202011_MNL.docx

10/74

www.baumer.com

11.20

3.2.2. Connecting

The encoder provides three M12 flange connectors.
Two M12 flange connectors (D-coding, according IEC 61076-2-101) serve for PROFINET connection.



For voltage supply use A-coded M12 connector only.



For the bus lines both D-coded M12 connectors may be used at will. However, together with a planned

topology it may be necessary to observe the correct assignment (P1/P2).



Seal up the unused cable gland using a sealing bolt (transport and dust protection).

No settings have to be done inside the encoder. In contrast to Profibus, there is no need for setting a node
ID or a terminating resistor. All settings required for encoder access are made in the engineering tool (e. g.
Siemens

Step7

or TIA

Portal).

Pin assignment

Supply voltage

PROFINET (Bus line)

1 x M12 flange connector (male)

2 x M12 flange connector (female)

A-coded

D-coded

Pin

Assignment

Pin

Assignment

UB (10...30 VDC)

TxD+

Do not connect

RxD+

GND

TxD-

Do not connect

RxD-

Port 1

Port 2

Power

Bus error

P2 Link /
Activity

P1 Link /
Activity

Collective
error SF

Содержание EAL580 MT Series











































































Результаты поиска

Содержание EAL580 MT Series

Отзывы:

Похожие инструкции для EAL580 MT Series

Бренды по названию

Популярные бренды

Baumer EAL580 MT Series, Руководство пользователя

Результаты поиска

Содержание EAL580 MT Series

Отзывы:

Похожие инструкции для EAL580 MT Series

Бренды по названию

Популярные бренды