background image

 

33 

 
 

 
 

 
 
 

My appliance isn’t working correctly 

 
 

o

 

The cooking zones are not functioning or will not switch on.

 

 

*

 

Check  that  the  mains  electrical  supply  to  the  appliance  is  correct 

and working. Check the mains fuse. 

 
 

o

 

The  residual  heat  indicator  has  not  come  on  after  I  have 

switched a cooking zone off.

 

 

*

 

The cooking zone has only been turned on for less than 30 seconds.

 

 

*

 

IMPORTANT: 

If  the  cooking  zone  does  appear  to  be  hotter  than 

50°C  or  has  been  activated  for  longer  than  30  seconds,  and  the 

residual  heat  indicator  has  not  come  on,  you  should  call  the 
Customer Care Department.

 

 
 

o

 

A humming sound is heard when a cooking zone is selected.

 

 

*

 

This is normal; the sound will disappear when the zone heats up.

 

 
 

o

 

The cooking zones have become discoloured. 

 

*

 

This  maybe  caused  by  burnt  on  remnants  of  food.  This  will  not 
affect the working of the appliance. However you should make sure 

that the cleaning instructions are being followed regularly.

 

 

 
 
 
 
 

 
 
 

Содержание HHC601






















Отзывы: