Baumatic BMEC9GGESS, Инструкция по эксплуатации

Страница: 7 / 32

CONNECTION TO THE MAINS SUPPLY THE APPLIANCE
MUST BE CONNECTED IN ACCORDANCE WITH THE RULES
IN FORCE, AND ONLY BY AN AUTHORIZED ELECTRICAL
INSTALLER.
WARNING:THIS APPLIANCE MUST BE EARTHED
Check that the power rating of the mains supply and of the sockets
are suitable for the maximum power of the appliance as indicated
on the specification plate. If the appliance does not come already
fitted with a plug, fit a regulation plug to the cable which is capable
of taking the power indicated on the specification plate
(fig. 10B ).
REPLACEMENT OF THE CABLE .
ALWAYS UNPLUG THE PLUG FROM THE CURRENT SOCKET
OR SWITCH OFF THE CURRENT ON THE POWER SUPPLY
LINE BY MEANS OF THE MAINS CIRCUIT SWITCH, BEFORE
CARRYING OUT ANY MAINTENANCE ON THE OVEN.
If the cable is damaged, fit a replacement in the following way:
- remove the mains cable and replace it with one of the same
length which is rubber insulated and suitable for the power rating
of the appliance.
The “yellow/green” earth wire, which must be connected to terminal
, has to be about 10 mm longer than the other wires; the “blue”
neutral wire has to be connected to the terminal marked with letter
N. The live wire must be connected to the terminal marked with
letter “L”.
TYPE AND SECTION OF SUPPLY CABLE
Applance type Alimentation monophasée 230 V~
Type of cable section
All gas Rubber H05 RR-F 3 x 0,75 mm2
All gas + elect. grill Rubber H05 RN-F 3 x 1, 5 mm2
The earth wire is yellow/green. If the plug fitted to the appliance,
and the socket, are incompatible, get a profesionnally qualified
person to fit the correct type of plug. If an appliance is not equipped
with supply cable and plug, the power supply must be fitted with
a disconnect switch in which the distance between contacts permits
total disconnection in accordance with overvoltage category III,
as required by installation regulations.
The yellow/green earth wire should not be controlled by the
switch.
The plug used for mains supply connection should be easy to get
at, once the appliance is in position.
CARE AND MAINTENANCE
ENAMELLED SURFACES
Clean with a damp sponge using soap and water.
Grease can be easily removed using hot water or a specific
cleansing agent for enamelled surfaces. Do not use abrasive
cleansers.
Do not leave any acid or alkaline substances (lemon juice, vinegar,
salt, etc.) on the enamel.
Clean the parts in stainless steel with specific cleansers for
stainless steel surfaces.
These detergents must be applied using a soft cloth.
GRIDS AND BURNERS
To clean the work-top burners, remove them by pulling upwards
and soak them for about 10 minutes in hot water with a little
detergent. After having cleaned and washed them, wipe them
carefully. Make sure that no burner hole is clogged.
Do not use steam cleaners to clean the oven.
Clean the burners once a week or more frequently if necessary.
MAKE SURE YOU HAVE ASSEMBLED THE BURNERS IN A
RIGHT WAY.
Removal of oven door
To make cleaning easier, remove the oven door as follows:
2) open the oven door completely.
3 ) flip the hinge hooks "A" outwards (see fig. 9B).
4) shut the oven door slowly until it reaches hooks "A" , making
sure these are locked into slots "B" of the oven door, as
shown in fig. 9C.
(Only where present, remove the inside door glass of the oven,
see fig. 9A).
5) Using both hands, push the oven door lightly inwards, toenable
the door hinges "C" to come away from the slots "D"
(see fig. 9D) and pull the door towards you until it is released
from the oven.
CAUTION:
Do not use rough or abrasive materials or sharp metal
scrapers to clean the glass doors of the oven since they may
scratch the surface and cause the glass to break.
Important: position the mains supply cable so that it is never
subjected to a temperature which is more than 50°C above ambient
temperature.
The electrical safety of the appliance can only be guaranteed
when it has been correctly connected to an efficient earthed power
supply, as laid down in the regulations for electrical safety.
Important: the manufacturer cannot be held responsible for any
damage to persons or objects due to the lack of an earth connection.
After cleaning it, reposition it correctly following the above steps
in the reverse order and flipping hooks "A" inwards before you
shut the oven door (fig. 9E).
The interior glass of the oven
(Only for models where present)
The interior glass of the oven door can be removed:
with the door in a semi-open position, use both hands to remove
the glass as shown in figures 9A.
After cleaning, refit the glass by proceeding in reverse order.
Fig. 9A
2
1
3
4
5
L
N
A
Before cleaning the appliance , disconnect the gas general
tap and unplug the appliance or disconnect power at the
main circuit breaker of the electrical system .
Do not clean the appliance surfaces when still hot.
IMPORTANT
Periodically check the external gas connection hole and
replace it when it shows any sign of deterioration. Do not
attempt to repair the gas hose under any cincumstances.
OVEN
Clean the enamelled parts with a damp sponge using soap and
water. Grease can be easily removed using hot water or a specific
cleansing agent for enamelled surfaces.
Do not use abrasive cleansers.
GB
ELECTRICAL CONNECTION
*
7
A A
A
B
A
C
D
A
Fig. 9C Fig. 9B
Fig. 9D Fig. 9E