background image

 

20

Hob guidelines 

 

o

 

The first few times the hob top is used, it may give off an acrid, 
burning smell. This smell will disappear completely with repeated 
use. 

 

o

 

The hob surface is fitted with cooking areas of different diameter 
and power. 

 

o

 

The positions where the heat will radiate from are clearly marked 
on the hob top. The saucepans must be positioned exactly on 
these zones for efficient heating to occur. Pans should have the 
same diameter as the cooking zone that they are being used on. 

 

o

 

You should not use saucepans with rough bottoms, as this can 
scratch the ceramic surface. 

 

o

 

Before use, make sure that the bottoms of the saucepans are 
clean and dry. 

 

o

 

When cold, the bottom of the pans should be slightly concave, as 
they expand when hot and lie flat on the surface of the hob. This 
will allow the heat to transfer more easily. 

 

o

 

The best thickness for the bottom of the pans is 2 – 3 mm of 
enamelled steel and 4 – 6 mm for stainless steel with sandwich 
type bottoms. 

 

o

 

If these rules are not followed, then there will be a great loss of 
heat and energy. Heat not absorbed by the saucepan, will spread 
to the hob, frame and surrounding cabinets. 

 

o

 

Preferably cover pans with a lid to permit cooking at a lower 
heat. 

 

o

 

Always cook vegetables and potatoes, etc. in as little water as 
possible, to reduce cooking times. 

 

o

 

Food or liquid that has high sugar content may damage the hob 
top if it comes into contact with the ceramic hob surface. Any 
spillages should be wiped up immediately, however this may not 
prevent the hob surface from becoming damaged. 

 

o

 

IMPORTANT: 

The ceramic hob surface is tough; however it is 

not unbreakable and can be damaged. Especially if pointed or 
hard objects are allowed to fall on it with some force. 

 

Содержание BHI340SS

































Отзывы: