Baumatic BDW9 Скачать руководство пользователя страница 13

Страница: 13 / 18

1234567890

Options

(Note: the various options must be selected before initiating the wash cycle)
• Delayed start : time delays for the initiation of the wash cycle can be set ranging from 1 to 16

hours. On the display, the delay period that was selected will be shown. The LED display will be
blinking during the entire delay period.
The selection of this setting option is confirmed when the number of the pre -selected programme
appears on the display.

• Half load : when choosing this wash cycle option, the following indication will appear on the

display: (¯=wash superior basket,_=wash inferior basket). The corresponding LED indication will be
illuminated.
The selection of this setting option is confirmed when the number of the pre-selected programme
appears on the display.

• Pre-wash cancel : This option is only available for programmes that include a pre-wash.

When pressing the button, the corresponding LED indication will be illuminated.
The selection of this setting option is confirmed when the number of the pre-selected programme
appears on the display.

• Drying : this programme option is carried out automatically by the programmes in whose cycle

it is included (see programme table). To modify the dryer setting, the drying button must be
pressed before initiating the chosen programme. On the display, the following information will ap-
pear: AO = no drying; A1= Drying 20’; A2 = Drying 35’; A3 = Drying 45’.
The corresponding LED indication will be illuminated.
The selection of this setting option is confirmed when the number of the pre -selected programme
appears on the display.

•

Note: In the models without the drying ventilator, this option is to be considered as waiting time at
the end of the cycle.

• Description of Start/Stop/Pause button
• It initiates the wash programme cycle (the buzzer sound indicates that the cycle has started).
• When you turn on the machine, using the ON/OFF button, the display indicates the number of the

last program that has been carried out. In cases where the previous program has not yet finished,
the display will flash the number of this program. In order to re-start it you must simply press the
“START” button , the remaining time that is necessary in order to finish the cycle will appear
automatically on the display.

(Situations such as this will occur each time that you open the machine when it is carrying out a

program).

• NOTE: should you wish to add or remove crockery etc.., to continue the washing program press

button 13 and close the door.

• Programme settings by mistake (change programme)
• Reset by using the start/stop/pause button : keep the button pressed until the buzzer stops

beeping (it produces a series of beeps).

• Repeat the select programme operation.

Note: If the programme has been initiated and has run beyond the water fill phase, the display
indicates “ “, Then, the appliance will discharge all water, and (after a prolonged buzzer sound)
the display will indicate the pre-selected programme setting.

Now, the appliance is ready for a new setting.

•

Note: Once you have opened the door, always press the Start button in order to restart the

dishwasher.

•

Activation / Elimination of the buzzer

b0 = Buzzer DEACTIVATED

b1 = Buzzer ACTIVATED
In order to access the setting of the BUZZER, keep the PROGRAM button pressed down when

you turn on the machine. The current setting “b1” will be visualised on the Display. In order to change
this setting, press the same button until you have selected the status of the buzzer that you desire.
Wait for approximately 6 seconds, without changing your choice, following this, the sound of the BUZZER
will confirm that the setting has been memorised.

•

End of cycle

Once the washing cycle is finished , the program number will appear lit up and still on the

display, if it is flashing wait for the end of the cycle.

Stop

After the wash cycle, the dishwasher stops automatically, then unit will emit a long buzz to indicate the
end of the wahing cycle. To turn it off, press the button on/off . After each wash cycle, the water
faucet must be closed to insulate the appliance from the water supply system.