manualshive.com logo in svg

Baum 714XLT, Инструкции по установке, Страница: 8 / 13

Поделиться
Скачать
Baum 714XLT Скачать руководство пользователя страница 8

               

How to install a perforator on a 714XLT 

 
 
(Continued from previous page) 
 

10. Slide  the 

female perforator collar

 until the wide groove of the female collar is under the 

perforator blade. Leave it loose for now. The 

perforator stripper

 should be between the 

perforator blade assembly and the female perforator collar. 

 

11. Slide  the 

left pullout tire

 you just removed back on the bottom slitter shaft until it is directly under 

the left pullout tire on the top slitter shaft and tighten the brass point set screw to secure the 
pullout tire assembly to the shaft. 

 

12. Replace  the 

left slitter shaft boxing

 on the slitter shaft in reverse order as you removed them. 

Install the 

socket head bolt

 that fastens the left slitter shaft boxing to the slitter shaft assembly 

and tighten it.  

 

13. Move  the 

female perforator collar

 until the sharp edge of the blade is against the edge of the 

wide groove in the female perforator collar and tighten the brass point set screw in the collar to 
secure it in place. The blade against the edge of the groove creates a scissors action as the shafts 
turn. 

THE PERFORATOR BLADE IS SHARP. CAUTION SHOULD BE EXERCISED WHEN 

WORKING AROUND THE PERFORATOR BLADE

. 

 

14. Replace the slitter shaft assembly in reverse order as it was removed. Extra care should be made 

to insure the slitter shaft boxings are secure on all four pins in the frame and the gears all mash 
properly. Turn the hand wheel a couple times to insure the slitter shaft assembly is in proper 
position.  

 

15. Raise  the 

perforator stripper

 until it is not rubbing the 

blade holder

 and along the side of the 

perforator blade

 and it will allow a sheet of paper to go under the stripper and above the female 

perforator collar without jamming them lock it in place. The purpose of the stripper is to strip the 
sheet off of the perforator blade otherwise the sheet would wrap around the top slitter shaft.  

 
16. Replace the feed table in reverse order it was removed. Again turn the hand wheel to be sure 

every thing is in the proper place and nothing is rubbing, run a sheet through to see if the 
perforator is in the proper location. If not loosen the setscrews and move the assemblies where 
you want them on the shafts and lock with the brass point setscrews. Turn the hand wheel to 
insure nothing is rubbing and check it again.    

 

 
Continued on next page… 
 
 

Baumfolder Corporation    P.O. Box 728  1660      Campbell Rd,  Sidney, Ohio USA  45365     Copyright © 2002 
 Phone  1-800-543-6107   or  1-937-492-1281    Fax   1-937-492-7280       email: [email protected]

 

Содержание 714XLT














Отзывы:

Нет отзывов