Baum 714XLT Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 13

Baum 714XLT Скачать руководство пользователя страница 10

Appendix C:

How to install or Remove

Score Blades on a Baum 714

**

UNPLUG POWER SUPPLY BEFORE WORKING ON ANY FOLDER **

The score blades are sharp. Extra care should be exercised to protect you from a cut
by the score blades.

BEFORE BEGINNING: On Air Feed and 714 AUTOFOLD units, disconnect the air and
vacuum hose, and on the AUTOFOLD, disconnect the electrical connection to the feed
table.

1. Lift up on the rear of the feed table and lift toward you to remove the feed table.

2. Under the feed table and just prior to the stacker is the

slitter shaft assembly

. On the left side of

the slitter shaft assembly is a

screw or plunger

that tightens against the frame to remove endplay

(movement from side to side). Loosen

screw or pull plunger.

3. Carefully lift both ends up even and then towards you and lay the slitter shaft assembly on a

worktable with the rubber pullout tires toward the worktable top.

4. Loosen the

socket head bolt

from the end of the tie bar that fastens the

left slitter shaft boxing

to the slitter shaft assembly. Remove the slitter shaft boxing from the slitter shafts.

5. Loosen the setscrew on the

left pullout tire assembly

and remove it from the top slitter shaft.

Leave the right pullout tie assembly in place.

6. To prepare the

score blade assembly

remove the two screws from the

blade holder collar

and

lay the

score blade

on the side of the

blade holder collar

and align the holes in the score blade

with the blade holder collar and replace the two screws. Do not tighten them now.

7. Slide the score blade and blade holder collar onto the top slitter shaft to the center of the top slitter

shaft and tighten the setscrew in the blade holder collar to lock it in position, and then tighten the
two screws to insure the score blade is tight against the blade holder collar.

8. Replace the

left pullout tire assembly

on the top slitter shaft and place it approximately three

inches from the score blade and tighten the setscrew to lock it in place. Keep all setscrews in line
so if you need to move them, you will not have to keep turning the slitter shaft.

9. Remove the

left pullout tire assembly

from the bottom slitter shaft.

10. Slide the

score collar assembly

on to the bottom slitter shaft until the

score blade

aligns with the

middle on the one-inch rubber in the

score collar assembly

. Tighten the setscrew to lock the

score collar in place.

(Continued)

Baumfolder Corporation P.O. Box 728 1660 Campbell Rd, Sidney, Ohio USA 45365 Copyright © 2002
Phone 1-800-543-6107 or 1-937-492-1281 Fax 1-937-492-7280 email: [email protected]

«
...
8
9
10
11
12
...
»

Содержание 714XLT














Отзывы:

Нет отзывов