Baudouin 12M26 Series Скачать руководство пользователя страница 38

Страница: 38 / 83

O&M Manual for PowerKit

M26 Series Diesel Engine

4.1 Preparations before Start

Oil



Adding of engine oil



Open the oil filler cap and add the

engine oil.



Using the dipstick to check the oil

level.

Fuel



Adding of fuel



The diesel fuel used shall meet the

specification.



The diesel fuel used must be clean.

It's better to place the diesel fuel

under stationary state for more

than 72 hours before adding. The

diesel fuel shall be added into the

fuel tan-k via the built-in filter

screen.

Coolant



Adding of coolant



The coolant is mixed from treated

clean water and anticorrosive

agent or antifreeze. Ensure to

strictly abide by the specification of

the additive manufacturer during

mixing.



Add coolant through the water filler

port of radiator or heat exchanger

and bleed the air from the cooling

circulation system.

Figure 4.1A-Adding of engine oil

Figure 4.1B-The fuel level

Figure 4.1C-Adding the coolant

Содержание 12M26 Series




















































































Результаты поиска

Содержание 12M26 Series

Отзывы:

Похожие инструкции для 12M26 Series

Бренды по названию

Популярные бренды

Baudouin 12M26 Series, Руководство по эксплуатации и обслуживанию

Результаты поиска

Содержание 12M26 Series

Отзывы:

Похожие инструкции для 12M26 Series

Бренды по названию

Популярные бренды