background image

 17

Battipav srl

GB

Store your tools in a save place 

•  When not in use, tools should be stored in dry and 

save places, out of the reach of children.

Don’t force tool

•  It will function better and in a safer way at the rate 

for which it was intended.

Use the right tool

•  Don’t  use  low  duty  tools  or  accessories  to  do 

the job of a heavy-duty tools. Don’t use tools for 

purposes not intended.

Dress properly

•  Rubber  gloves  and  non-skid  footwear  are 

recommended when working outdoors. Wear 

protective hair covering to contain long hair. Use 

safety glasses. 

•  Use a mask if working operations are dusty.

Don’t abuse cord

•  Never carry tool by cord or yank it to disconnect it 

from socket. 

•  Keep cord from heat, oil and sharp edges.

Avoid unsteady positions

•  Be sure to work in a safe and balanced position.

Maintain tools with care

•  Keep tools sharp and clean for better and safer 

performance. 

•  Follow all maintenance advice and instructions to 

replace accessories subject to wear. Inspect tool 

cords periodically and, if damaged, have them 

repaired by an authorised expert. Check extension 

cords periodically and replace them if damaged. 

Keep handles dry, clean and free from oil and 

grease.

Disconnect tools

•  When  not  in  use,  before  servicing,  and  when 

changing accessories subject to wear. 

Remove service keys from tool 

•  Form the habit of checking to see that keys and 

adjusting wrenches are removed from tool before 

turning it on.

Avoid unintentional starting

•  Be sure that the switch is off when plugging in the 

tool. 

Extension cords for outdoor works

•  When  tool  is  used  outdoors,  use  only  extension 

cords intended for this particular use and so 

marked.

Stay alert

•  Watch what you are doing. Use common sense. 

Do not operate tool when you are inattentive.

Check tool for damaged parts

•  Before  further  use  of  the  tool,  check  it  and  the 

safety devices for damages and be sure that 

they operate properly. Check for functioning 

and binding of moving parts, breakage of parts, 

correct mounting, and any other conditions that 

may affect the correct operation of the tool. 

•  Damaged  safety  devices  or  other  parts  should 

be properly repaired or replaced by an authorised 

Service Centre unless otherwise indicated 

elsewhere in this instruction manual. 

•  Have  defective  switches  replaced  by  an 

authorised Service Centre. 

•  Do not use tool if its switch cannot be turned on or 

off.

Warning

•  For  your  personal  safety  use  only  accessories 

recommended in this instruction manual or in 

the relevant catalogues The use of any other 

accessory or attachment other than those 

recommended in this instruction manual or in the 

relevant catalogue may present a risk of personal 

injury.

have tools repaired by qualified personnel 

•  This  electric  appliance  is  in  accordance  with 

the  safety  rules  in  force.  Only  qualified  experts 

may carry out repairing of electric appliances 

otherwise it may cause considerable danger for 

the user.

Содержание VIP 845
















Отзывы: