background image

9170800990 Rev M 

BE1-87G Functional Description 

3-3 

Comparator 

The comparator provides the variable percentage characteristic of the relay as follows. 

When I

R

  is less than nominal (5 Aac for sensing input range 1 or 1 Aac for sensing input range 2), the 

comparator provides an output signal whenever I

OP

 exceeds the front panel sensitivity setting. 

Restraint Current Less than Nominal 

When I

R

 is greater than nominal (5 Aac for sensing input range 1 or 1 Aac for sensing input range 2), the 

front panel sensitivity switch setting (threshold) is increased by adding it to a scaled value representing 
one half of I

R

 minus nominal (5 Aac for sensing input range 1 or 1 Aac for sensing input range 2). 

Restraint Current Greater than Nominal 

Output Relays 

When the current difference exceeds the variable percentage limit (sensitivity switch setting), the 
comparator output energizes the output relays. (In BE1-87G models with three-phase sensing, the 
outputs are ORed together so that the output relays energize  if the current difference of any one phase 
exceeds the limit.) When the current difference decreases below 90% of the variable percentage 
threshold, the output relays reset. 

The main output relay contacts are either normally-open or normally-closed and are accessed at case 
terminals 1 and 10. Normally-open contacts are provided on BE1-87G relays with a style number of xxE-
xxx-xxxxx and normally-closed contacts are provided on relays with a style number of xxG-xxx-xxxxx. 

Main Output Relay 

An optional pair of contacts, accessed at case terminals 2 and 5, can be specified. The auxiliary output 
contacts change state when the main output contacts operate and are available in a normally-open or 
normally-closed configuration. Normally-open auxiliary contacts are provided on BE1-87G relays with 
style number xxx-xxx-xxx1x and normally-closed auxiliary contacts are provided on relays with style xxx-
xxx-xxx2x. 

Auxiliary Output Relay (Optional) 

Optionally, the auxiliary output relay can be specified to function as a power supply status output. This 
normally-closed output is energized open during normal operation. When relay control power is lost or an 
internal power supply failure occurs, the relay de-energizes and closes the contacts at terminals 2 and 5. 

Target Indicators (Optional) 

Target indicators are optional components selected when a relay is ordered. The electronically latched 
and reset targets consist of red LED indicators located on the relay front panel. Latched targets are reset 
by operating the target reset switch on the front panel. If relay operating power is lost, any illuminated 
(latched) targets are extinguished. When relay operating power is restored, the previously latched targets 
are restored to their latched state. 

A relay can be equipped with either  internally operated targets or current operated targets. Both target 
types are reset by operating the target reset switch. 

The relay trip outputs are directly applied to drive the target indicators. The indicators are illuminated 
regardless of the current level in the trip circuits. 

Internally Operated Targets 

Current operated targets are triggered by closure of the corresponding output contact 

Current Operated Targets 

and

 

 the presence of 

at least 200 milliamperes of current flowing in the trip circuit. 

NOTE 

Prior to September 2007, the BE1-87G target indicators consisted of 
magnetically latched, disc indicators. These mechanically latched target 
indicators have been replaced by the electronically latched LED targets in use 
today. 

Содержание BE1-87G

































































Отзывы: