Basler BE1-50B-230 Скачать руководство пользователя страница 12

Страница: 12 / 71

1-2

BE1-50/51B-230/-234 General Information

9252000894 Rev D

SPECIFICATIONS

BE1-50/51B-230 and BE1-50/51B-234 electrical and physical specifications are listed in the following
paragraphs.

Time Overcurrent (51) Element

BE1-50/51B-230 Pickup

Setting Range:

0.5 to 15.9 Aac

Setting Increment:

0.1 Aac

Accuracy: Sum

2% and

25 mAac

BE1-50/51B-234 Pickup

Setting Range:

0.1 to 3.18 Aac

Setting Increment:

0.02 Aac

Accuracy: Sum

2% and

5 mAac

Dropout

Dropout occurs at 95% of pickup value.

Characteristic Curves

Available curve types follow IEEE Standard C37.112 (1996) and emulate standard GE IAC, ABB CO, and
BS142 curves. Appendix A,

Characteristic Curves

illustrates the available curves and lists the applicable

constants.

Curve Types:

Short Inverse, Long Inverse, Definite Time, Moderately Inverse, Inverse,
Very Inverse, Extremely Inverse, BS142 Very Inverse, BS142 Extremely
Inverse, Fixed Time

Time Multiplier:

11 curves for each characteristic

Timing Accuracy:

1 cycle,

2%. This accuracy applies to the range of 1.3 to 40 times tap

and is for a given measured multiple of tap.

Fixed Timing

Setting Range:

0.1 to 9.9 s

Setting Increment:

0.1 s

Timing Accuracy:

1 cycle,

2% of the time to trip for time dial settings

≥

0.1.

Reset

Integrating:

Simulates the disk reset of electromechanical relays and begins when
the current decreases below 95% of pickup. Appendix A,

Characteristic

Curves

illustrates the integrating reset characteristic curve and equation.

Instantaneous:

Reset occurs within 16 ms of when the current decreases below 95% of
the pickup level.

Instantaneous Overcurrent A (50-A) Element

BE1-50/51B-230 Pickup

Setting Range:

2 to 99 Aac

Setting increment:

1 Aac

Accuracy: Sum

2% and

25 mAac

BE1-50/51B-234 Pickup

Setting Range:

0.4 to 19.8 Aac

Setting increment:

0.2 Aac

Accuracy: Sum

2% and

5 mAac

Dropout

Dropout occurs at 95% of pickup value.

Time Delay

Switch selectable—no intentional delay (SW3-2 open/off) or a fixed delay of 100 ms (SW3-2 closed/on).
Appendix A,

Characteristic Curves

illustrates the characteristic curve for the 50-A and 50-B elements.

Содержание BE1-50B-230








































































Результаты поиска

Содержание BE1-50B-230

Отзывы:

Похожие инструкции для BE1-50B-230

Бренды по названию

Популярные бренды

Basler BE1-50B-230, Инструкция по эксплуатации

Результаты поиска

Содержание BE1-50B-230

Отзывы:

Похожие инструкции для BE1-50B-230

Бренды по названию

Популярные бренды