Basler BE1-50B-230 Скачать руководство пользователя страница 45

Страница: 45 / 71

9252000894 Rev D

BE1-50/51B-230/-234 Testing

5-7

Model BE1-50/51B-234 (One Ampere Sensing Input)

Time Overcurrent (51) Pickup

1. Connect and configure the relay for 51 pickup testing:

a. Connect the test setup shown in Figure 5-5.

b. Set circuit board switch SW3 as follows:

SW3-1 = ON for 50 Hz operation or OFF for 60 Hz operation
SW3-2 = OFF (no additional time delay for the 50-A element)
SW3-3 = ON (GE IAC type characteristic curves)
SW3-4 = ON (integrating reset characteristic)

c. Set the TIME DIAL to 0.0.

d. Set CURVE to S.

e. Set TIME PICKUP to 0.1.

Set INST PICKUP (50-A) to 18.0.

g. Set INST PICKUP (50-B) (accessed at the top side of the assembly) to F0 (3.0 Aac).

2. Apply and increase current to terminals 5 and 6 until the Active/Pickup LED turns red. The applied

current should be no greater than 0.11 Aac.

3. Decrease the applied current until the Active/Pickup LED changes from red to green and then off.

4. Set TIME PICKUP to 0.44.

5. Slowly increase current to terminals 5 and 6 until the Active/Pickup LED turns red. The applied

current should be between 0.426 and 0.454 Aac.

6. Reduce the applied current to zero.

Time Dial

1. Connect and configure the relay for time dial testing:

a. Connect the test setup shown in Figure 5-5.

b. Set circuit board switch SW3 as follows:

c. Set TIME DIAL to 4.5.

d. Set CURVE to S.

e. Set TIME PICKUP to 0.2.

Set INST PICKUP (50-A) to 18.0.

g. Set INST PICKUP (50-B) (accessed at the top side of the assembly) to F0 (3.0 Aac).

2. Prepare to apply 0.3 Aac to terminals 5 and 6 and record the elapsed time from when current is

applied until the 51 output contacts close.

3. Apply the current (step from 0 to 0.3 Aac) and record the elapsed time. The elapsed time should be

between 0.345 and 0.424 seconds. (This tolerance is greater than

2% because it is the

accumulation of both pickup and timing tolerances.)

4. Remove the input current.

Integrating Reset

1. Connect and configure the relay for integrating reset testing.

a. Connect the test setup shown in Figure 5-5.

b. Set circuit board switch SW3 as follows:

c. Set TIME DIAL to 9.9

Содержание BE1-50B-230








































































Результаты поиска

Содержание BE1-50B-230

Отзывы:

Похожие инструкции для BE1-50B-230

Бренды по названию

Популярные бренды

Basler BE1-50B-230, Инструкция по эксплуатации

Результаты поиска

Содержание BE1-50B-230

Отзывы:

Похожие инструкции для BE1-50B-230

Бренды по названию

Популярные бренды