Installation
Please proceed in the following order:
1. Attach the enclosed rubber washer onto the hand shaft.
2. Attach the clock movement from the back through the borehole to the clock-face and align it horizontally
with the suspension bracket facing upwards.
3. Place the washer above the hand shaft and tighten the clock movement with the middle hexagon nut. In
this process, make sure you don’t tighten the nut too fi rmly to avoid twisting and damages.
4.
Insert the hour hand fi rst and then the minute hand gently to the hand shaft and secure the minute hand
using the small knurled nut. If a second hand is used, the cap nut can be used to cover the hand shaft.
5. Finally insert the second hand into the hand shaft, if used.
6. Align all the hands of the clock to the 12:00 o’clock position.
7. Make sure the hands are aligned parallel to the clock-face so that they don’t touch each other during
operation or rub against the clock-face.
8. Attach the pendulum weight onto the pendulum rod.
9. Unfasten the pendulum suspension bracket from the locking mechanism on the housing’s rear and mount
the pendulum.
The minute and second hands as well as the pendulum should not exceed the following
dimensions and weight:
Minute hand: max. 160 mm / 6 g
Second hand: max. 130 mm / 6g
The pendulum must be able to swing freely.
Inserting the Battery/Rechargeable Battery
• Insert a battery of type 1.5 V Mignon/AA into the battery compartment on the back of the casing, while
observing the correct polarity. The correct polarity is indicated in the battery compartment.
• Replacing the battery is necessary when the clock stops or the accuracy of movement decreases.
A rechargeable battery may be used, but due to the lower voltage output (rechargeable battery
= 1.2V, standard battery = 1.5V) and the lower capacity, the service life is shorter.
Setting the time
Set the time by turning the adjustment knob with the clock symbol on the back of the case. The adjustment
knob can be rotated in both directions here.
Care and cleaning
• Do not use any aggressive cleaning agents, rubbing alcohol or other chemical solutions as they can cause
damage to the housing and malfunctioning.
•
To clean the clock movement, a dry, soft and clean cloth is sufficient.
Disposal
a) Product
Electronic devices are recyclable waste and must not be disposed of in the household waste. At
the end of its service life, dispose of the product according to the relevant statutory regulations.
Remove any inserted batteries and dispose of them separately from the product.
b) (Rechargeable) Batteries
You as the end user are required by law (Battery Ordinance) to return all used (rechargeable)
batteries. Disposing of them in the household waste is prohibited.
Contaminated (rechargeable) batteries are labelled with this symbol to indicate that disposal
in the domestic waste is forbidden. The designations for the heavy metals involved are: Cd =
Cadmium, Hg = Mercury, Pb = Lead (name on batteries, e.g. below the trash icon on the left).
Used (rechargeable) batteries can be returned to collection points in your municipality, our stores or wherever
(rechargeable)batteries are sold.
You thus fulfill your statutory obligations and contribute to the protection of the environment.
Technical data
Battery ...........................................................1,5 V Battery Type AA/Mignon
Battery lifespan ..............................................approx. 1 year
Shaft ..............................................................16,8 mm
Hand borehole ...............................................2,8 x 3,8 / 5 mm, slotted hole/round
Clockface thickness .......................................max. 5 mm
Mounting borehole .........................................8 mm
Operating conditions ......................................0 to +55 ºC, 0 – 90 % rH
Storage conditions .........................................-20 to +70 ºC, 0 – 90 % rH
Dimensions (W x H x D) ................................56 x 116 x 26 mm (without shaft and pendulum)
Weight ...........................................................84 g
Operating instructions
Quartz Pendulum Clock Movement 16.8 mm
Item no. 1911208
Intended use
The quartz pendulum clock movement is used to display the time. To this end, a dial is installed and provided
with suitable hands as well as a pendulum. The watch may only be operated by a battery (for the type, refer
to “Technical Data”).
It is intended for indoor use only. Do not use it outdoors. Contact with moisture, e.g. in bathrooms, must be
avoided under all circumstances.
For safety and approval purposes, you must not rebuild and/or modify this product. If you use the product
for purposes other than those described above, the product may be damaged. In addition, improper use can
cause hazards such as short circuiting, fire, electric shock etc. Read the instructions carefully and keep them.
Make this product available to third parties only together with its operating instructions.
This product complies with the statutory national and European requirements. All company names and
product names are trademarks of their respective owners. All rights reserved.
Delivery content
• Quartz Pendulum Clock Movement
•
Assembly material (4x fixing nut, 1x rubber washer)
• Pendulum
• Shaft
• Operating instructions
Latest operating instructions
Download the latest operating instructions via the link www.conrad.com/downloads or scan the QR code
shown. Follow the instructions on the website.
Explanation of symbols
An exclamation mark in a triangle indicates important instructions in this operating manual that
absolutely have to be observed.
The arrow symbol indicates specific tips and advice on operation.
Safety instructions
Read the operating instructions carefully and especially observe the safety information.
If you do not follow the safety instructions and information on proper handling in this
manual, we assume no liability for any resulting personal injury or damage to property.
Such cases will invalidate the warranty/guarantee.
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. This may become dangerous playing
material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity,
moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and protect it
from any accidental use. Safe operation can no longer be guaranteed if the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height can damage
the product.
• Never use the product immediately after it has been brought from a cold room into a warm
one. The condensation generated could destroy the product. Allow the product to reach room
temperature before connecting it to the power supply and putting it to use. This process may
take several hours.
• Correct polarity must be observed while inserting the (rechargeable) batteries.
• (Rechargeable) batteries should be removed from the device if it is not used for a long period
of time to avoid damage through leaking. Leaking or damaged (rechargeable) batteries might
cause acid burns when in contact with skin, therefore use suitable protective gloves to handle
corrupted (rechargeable) batteries.
• (Rechargeable) batteries must be kept out of reach of children. Do not leave (rechargeable)
batteries lying around, as there is risk, that children or pets swallow them.
• All (rechargeable) batteries should be replaced at the same time. Mixing old and new
(rechargeable) batteries in the device can lead to (rechargeable) battery leakage and device
damage.
•
(Rechargeable) batteries must not be dismantled, short-circuited or thrown into fire. Never
recharge non-rechargeable batteries. There is a risk of explosion!
• Consult an expert when in doubt about operation, safety or connection of the device.
•
Maintenance, modifications and repairs are to be performed exclusively by an expert or at a
qualified shop.
• If you have questions which remain unanswered by these operating instructions, contact our
technical support service or other technical personnel.
This is a publication by Conrad Electronic SE, Klaus-Conrad-Str. 1, D-92240 Hirschau (www.conrad.com).
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the capture in
electronic data processing systems require the prior written approval by the editor. Reprinting, also in part, is prohibited.
This publication represent the technical status at the time of printing.
Copyright 2019 by Conrad Electronic SE.
*1911208_v1_0419_02_hk_m_en
