background image

 

 

 

- 44 - 

 

Never open the housing of the device. If the electrical connections 
are damaged or electrical or mechanical design is changed, there is 
a risk of electrical shock. 

 

Never immerse the connecting cable and the the power plug in water 
or other liquids. 

 

Never use abrasive agents and make sure no water gets into the 
device. 

 

Never handle the device with wet hands or while standing on the wet 
floor. 

 

Disconnect the device from the power supply: 

-

  when the device is not used, 

-

  in the case of interruptions during the operation of the device, 

-

  before cleaning the device.

 

 HOT SURFACE! Danger of burns and injury! 

To avoid the hazard results please follow the safety instructions below. 

 

 

During operation, the surface of the device becomes very hot! Do not 
touch the hot surface of the device with bare hands! Hold the device 
during operation only at the handles and control elements envisaged 
for this. 

 

Even after switching off the surface of the device and the cooking 
space as well as food in the containers remain hot for quite some 
time. In order to take out the food from the cooking space, always 
apply thermal gloves. 

 

In the course of opening the combi steamer door the hot steam can 
may escape, so be particularly careful. 

 

Let the device cool down sufficiently before cleaning it. 

Содержание E 10110 / 116531










































Отзывы: