background image

MODEL 227C

DIFFERENTIAL PRESSURE INDICATOR

w/224C DPU

Installation Manual

Version 00K25c

ID#10120

11/2000

SECTION 1 - INTRODUCTION

General

The Model 227C DP Indicator measures liquid flow or liquid level. For flow
measurements, the instrument is connected to the low and high pressure sides
of a primary device (e.g., orifice plate, venturi tube, or flow tube) located in the
process run. For liquid level, the instrument is connected to measure changes in
differential pressure relative to variations of liquid height in a vessel.

Theory of Operation

The bellows within the DPU moves in response to changes in the differential
pressure measured at the primary device installed in the process system.
Movement of the bellows (in direction of decreasing pressure) is mechanically
transferred to the indicator mechanism, which in turn positions the indicating
pointer.

SAFETY

Before installing this instrument

, become familiar with the installation instructions

in Section 2. 

WARNING

 notes that appear on the following pages of this manual

should be reviewed before proceeding: 

3

6

, and 

7

.

WARNING

 notes indicate the presence of a hazard which 

can

 cause 

severe

personal injury, death, or substantial property damage if warning is ignored.

CONTENTS

Section 1 - Introduction ............................................................. Page 1
Section 2 - Installation ............................................................... Page 2
Section 3 - Maintenance ............................................................ Page 4
Section 4 - Troubleshooting ....................................................... Page 9
Section 5 - Installation Drawings................................................. Page 10
Section 6 - Parts/Drawing List ................................................... Page 14
DPU Specifications ................................................................... Page 19
Instrument Specifications ........................................................... Back Page

Содержание 227C





















Отзывы: