Operational Instruction
(Original)
Distribution box
Type 07-5103-…./…., 07-5105-
…./…., 07-5106-…./…. and 07-5107-…./….
BARTEC
Varnost d.o.o.
Cesta 9.avgusta 59
1410 Zagorje ob Savi
Slovenia
Tel.: +386 59 221 471
Fax: +386 59 221 470
[email protected]
www.bartecvarnost.si
Reservation
Technical data subject to change without notice. Changes, errors and
misprints may not be used as a basis for any claim for damages.
EN 3/3
V
S
–
1
1
01
3
01
(
is
su
e
N
o
I
/
2.
11
.2
01
6)
Connecting conductors
Risk of serious injury due to incorrect
proceedings.
All terminal positions, including the unused
ones, are to be tightened firmly.
The connections must be secured against
self-loosening.
Take care when connecting conductors:
•
Remove approx. 6 mm (0.24 in) conduc-
tor insulation from the cores.
•
Prepare the ends of fine-stranded and
multi-stranded conductors: Crimp wire
end sleeves with suitable crimping tools in
order to achieve a constant pressure
quality.
NOTICE! Take care not to damage
the individual wires.
•
Release terminals.
•
Put the wire in the terminals.
•
Tight the terminals with a maximum
permissible torque depending from the
size of the screws. For information about
tightening torque of the terminal screw,
see the manufacturer´s catalogue.
Commissioning
Before commissioning, check that:
•
The distribution box has been installed in
compliance with regulations.
•
The distribution box is not damaged.
•
The connection has been established
properly.
•
The cables have been laid correctly.
•
All screws have been tightened securely.
•
The distribution box functions perfectly.
Note
Electrical equipments, before putting into
operation, and at certain time intervals, are to
be subjected and to examination by an electri-
cal expert.
Operation
Death or serious injury through improper
use.
The distribution box may be operated only
within the technical limits that apply to it
(see page 1).
Maintenance and fault clearance
Risk of serious injury due to incorrect
proceedings.
Only authorized qualified personnel are
allowed to do any of the work relating to
maintenance and fault clearance.
IEC/EN 60079-17 must be observed.
Do not open the distribution box when
energized.
Risk of serious injury due to damaged parts.
If any part of the equipment is damaged, it
should be exchanged only with original
parts (e.g. sealing gasket/cable glands/
terminals).
Maintenance
Risk of serious injury due to electrostatic
charging.
For type 07-5106-…./…., 07-5107-…./….,
and for windows with surface resistance of
>10
9
C potential electrostatic charging
hazard exist. Only wet cleaning is allowed.
The operator of the distribution box must keep
it in good condition, monitor it and clean it
regularly. He has to determine the maintenance
intervals depending on the conditions of use.
Within the scope of maintenance:
•
Check distribution box, cable entries,
sealings, and cables regularly for cracks
and damage.
•
Make sure that they are properly estab-
lished.
Fault clearance
The distribution box is defective if the encapsu-
lation is damaged and/or if one of the compo-
nents does not function any longer.
In this case:
•
Replace defective parts in the encapsula-
tion with original parts immediately.
•
Replace or repair the defective compo-
nents with original parts.
Note
Follow the components mounting instruc-
tions/operating instructions to replace or repair
the components.
Accessories, spare parts
For accessories and spare parts, see BARTEC
catalogue.
Disposal
The distribution box and its components contain
metal and plastic parts.
Therefore the statutory requirements for dispos-
ing of electronic scrap must be observed (e.g.
disposal by an approved disposal company).
Note
Ensure environmentally friendly disposal of all
components according to legal regulations.
Service Address
BARTEC VARNOST d.o.o.
Cesta 9.avgusta 59
1410 Zagorje ob Savi Slovenia
Tel.:
+386 59 221 471
Fax:
+386 59 221 470
